+ QCA_ACS_MODE_IEEE80211ANY,
+};
+
+/**
+ * enum qca_wlan_vendor_features - Vendor device/driver feature flags
+ *
+ * @QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD: Device supports key
+ * management offload, a mechanism where the station's firmware
+ * does the exchange with the AP to establish the temporal keys
+ * after roaming, rather than having the user space wpa_supplicant do it.
+ * @QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY: Device supports automatic
+ * band selection based on channel selection results.
+ * @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports
+ * simultaneous off-channel operations.
+ * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P
+ * Listen offload; a mechanism where the station's firmware takes care of
+ * responding to incoming Probe Request frames received from other P2P
+ * Devices whilst in Listen state, rather than having the user space
+ * wpa_supplicant do it. Information from received P2P requests are
+ * forwarded from firmware to host whenever the host processor wakes up.
+ * @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits
+ */
+enum qca_wlan_vendor_features {
+ QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0,
+ QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1,
+ QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2,
+ QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3,
+ NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */
+};
+
+/**
+ * enum qca_wlan_vendor_attr_data_offload_ind - Vendor Data Offload Indication
+ *
+ * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION: Session corresponding to
+ * the offloaded data.
+ * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL: Protocol of the offloaded
+ * data.
+ * @QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT: Event type for the data offload
+ * indication.
+ */
+enum qca_wlan_vendor_attr_data_offload_ind {
+ QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_SESSION,
+ QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_PROTOCOL,
+ QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_EVENT,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_MAX =
+ QCA_WLAN_VENDOR_ATTR_DATA_OFFLOAD_IND_AFTER_LAST - 1
+};
+
+enum qca_vendor_attr_get_preferred_freq_list {
+ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_INVALID,
+ /* A 32-unsigned value; the interface type/mode for which the preferred
+ * frequency list is requested (see enum qca_iface_type for possible
+ * values); used in GET_PREFERRED_FREQ_LIST command from user-space to
+ * kernel and in the kernel response back to user-space.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_IFACE_TYPE,
+ /* An array of 32-unsigned values; values are frequency (MHz); sent
+ * from kernel space to user space.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_MAX =
+ QCA_WLAN_VENDOR_ATTR_GET_PREFERRED_FREQ_LIST_AFTER_LAST - 1
+};
+
+enum qca_vendor_attr_probable_oper_channel {
+ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_INVALID,
+ /* 32-bit unsigned value; indicates the connection/iface type likely to
+ * come on this channel (see enum qca_iface_type).
+ */
+ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_IFACE_TYPE,
+ /* 32-bit unsigned value; the frequency (MHz) of the probable channel */
+ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_FREQ,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_MAX =
+ QCA_WLAN_VENDOR_ATTR_PROBABLE_OPER_CHANNEL_AFTER_LAST - 1
+};
+
+enum qca_iface_type {
+ QCA_IFACE_TYPE_STA,
+ QCA_IFACE_TYPE_AP,
+ QCA_IFACE_TYPE_P2P_CLIENT,
+ QCA_IFACE_TYPE_P2P_GO,
+ QCA_IFACE_TYPE_IBSS,
+ QCA_IFACE_TYPE_TDLS,
+};
+
+enum qca_set_band {
+ QCA_SETBAND_AUTO,
+ QCA_SETBAND_5G,
+ QCA_SETBAND_2G,
+};
+
+/**
+ * enum qca_access_policy - Access control policy
+ *
+ * Access control policy is applied on the configured IE
+ * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE).
+ * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY.
+ *
+ * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match
+ * the specific configuration (IE) set, i.e., allow all the
+ * connections which do not match the configuration.
+ * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match
+ * the specific configuration (IE) set, i.e., deny all the
+ * connections which do not match the configuration.
+ */
+enum qca_access_policy {
+ QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED,
+ QCA_ACCESS_POLICY_DENY_UNLESS_LISTED,
+};
+
+/**
+ * enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture
+ * @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32)
+ * @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value
+ * @QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE: Unsigned 64 bit Synchronized
+ * SOC timer value at TSF capture
+ */
+enum qca_vendor_attr_tsf_cmd {
+ QCA_WLAN_VENDOR_ATTR_TSF_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_TSF_CMD,
+ QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE,
+ QCA_WLAN_VENDOR_ATTR_TSF_SOC_TIMER_VALUE,
+ QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_TSF_MAX =
+ QCA_WLAN_VENDOR_ATTR_TSF_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_tsf_operation: TSF driver commands
+ * @QCA_TSF_CAPTURE: Initiate TSF Capture
+ * @QCA_TSF_GET: Get TSF capture value
+ * @QCA_TSF_SYNC_GET: Initiate TSF capture and return with captured value
+ */
+enum qca_tsf_cmd {
+ QCA_TSF_CAPTURE,
+ QCA_TSF_GET,
+ QCA_TSF_SYNC_GET,
+};
+
+/**
+ * enum qca_vendor_attr_wisa_cmd
+ * @QCA_WLAN_VENDOR_ATTR_WISA_MODE: WISA mode value (u32)
+ * WISA setup vendor commands
+ */
+enum qca_vendor_attr_wisa_cmd {
+ QCA_WLAN_VENDOR_ATTR_WISA_INVALID = 0,
+ QCA_WLAN_VENDOR_ATTR_WISA_MODE,
+ QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_WISA_MAX =
+ QCA_WLAN_VENDOR_ATTR_WISA_AFTER_LAST - 1
+};
+
+/* IEEE 802.11 Vendor Specific elements */
+
+/**
+ * enum qca_vendor_element_id - QCA Vendor Specific element types
+ *
+ * These values are used to identify QCA Vendor Specific elements. The
+ * payload of the element starts with the three octet OUI (OUI_QCA) and
+ * is followed by a single octet type which is defined by this enum.
+ *
+ * @QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST: P2P preferred channel list.
+ * This element can be used to specify preference order for supported
+ * channels. The channels in this list are in preference order (the first
+ * one has the highest preference) and are described as a pair of
+ * (global) Operating Class and Channel Number (each one octet) fields.
+ *
+ * This extends the standard P2P functionality by providing option to have
+ * more than one preferred operating channel. When this element is present,
+ * it replaces the preference indicated in the Operating Channel attribute.
+ * For supporting other implementations, the Operating Channel attribute is
+ * expected to be used with the highest preference channel. Similarly, all
+ * the channels included in this Preferred channel list element are
+ * expected to be included in the Channel List attribute.
+ *
+ * This vendor element may be included in GO Negotiation Request, P2P
+ * Invitation Request, and Provision Discovery Request frames.
+ *
+ * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element.
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID. The payload of this
+ * vendor specific element is defined by the latest P802.11ax draft.
+ * Please note that the draft is still work in progress and this element
+ * payload is subject to change.
+ *
+ * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element.
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID. The payload of this
+ * vendor specific element is defined by the latest P802.11ax draft.
+ * Please note that the draft is still work in progress and this element
+ * payload is subject to change.
+ */
+enum qca_vendor_element_id {
+ QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0,
+ QCA_VENDOR_ELEM_HE_CAPAB = 1,
+ QCA_VENDOR_ELEM_HE_OPER = 2,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_scan - Specifies vendor scan attributes
+ *
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_IE: IEs that should be included as part of scan
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES: Nested unsigned 32-bit attributes
+ * with frequencies to be scanned (in MHz)
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS: Nested attribute with SSIDs to be scanned
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES: Nested array attribute of supported
+ * rates to be included
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE: flag used to send probe requests
+ * at non CCK rate in 2GHz band
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS: Unsigned 32-bit scan flags
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE: Unsigned 64-bit cookie provided by the
+ * driver for the specific scan request
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_STATUS: Unsigned 8-bit status of the scan
+ * request decoded as in enum scan_status
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC: 6-byte MAC address to use when randomisation
+ * scan flag is set
+ * @QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK: 6-byte MAC address mask to be used with
+ * randomisation
+ */
+enum qca_wlan_vendor_attr_scan {
+ QCA_WLAN_VENDOR_ATTR_SCAN_INVALID_PARAM = 0,
+ QCA_WLAN_VENDOR_ATTR_SCAN_IE,
+ QCA_WLAN_VENDOR_ATTR_SCAN_FREQUENCIES,
+ QCA_WLAN_VENDOR_ATTR_SCAN_SSIDS,
+ QCA_WLAN_VENDOR_ATTR_SCAN_SUPP_RATES,
+ QCA_WLAN_VENDOR_ATTR_SCAN_TX_NO_CCK_RATE,
+ QCA_WLAN_VENDOR_ATTR_SCAN_FLAGS,
+ QCA_WLAN_VENDOR_ATTR_SCAN_COOKIE,
+ QCA_WLAN_VENDOR_ATTR_SCAN_STATUS,
+ QCA_WLAN_VENDOR_ATTR_SCAN_MAC,
+ QCA_WLAN_VENDOR_ATTR_SCAN_MAC_MASK,
+ QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SCAN_MAX =
+ QCA_WLAN_VENDOR_ATTR_SCAN_AFTER_LAST - 1
+};
+
+/**
+ * enum scan_status - Specifies the valid values the vendor scan attribute
+ * QCA_WLAN_VENDOR_ATTR_SCAN_STATUS can take
+ *
+ * @VENDOR_SCAN_STATUS_NEW_RESULTS: implies the vendor scan is successful with
+ * new scan results
+ * @VENDOR_SCAN_STATUS_ABORTED: implies the vendor scan was aborted in-between
+ */
+enum scan_status {
+ VENDOR_SCAN_STATUS_NEW_RESULTS,
+ VENDOR_SCAN_STATUS_ABORTED,
+ VENDOR_SCAN_STATUS_MAX,
+};
+
+/**
+ * enum qca_vendor_attr_ota_test - Specifies the values for vendor
+ * command QCA_NL80211_VENDOR_SUBCMD_OTA_TEST
+ * @QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE: enable ota test
+ */
+enum qca_vendor_attr_ota_test {
+ QCA_WLAN_VENDOR_ATTR_OTA_TEST_INVALID,
+ /* 8-bit unsigned value to indicate if OTA test is enabled */
+ QCA_WLAN_VENDOR_ATTR_OTA_TEST_ENABLE,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_OTA_TEST_MAX =
+ QCA_WLAN_VENDOR_ATTR_OTA_TEST_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_vendor_attr_txpower_scale - vendor sub commands index
+ *
+ * @QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE: scaling value
+ */
+enum qca_vendor_attr_txpower_scale {
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_INVALID,
+ /* 8-bit unsigned value to indicate the scaling of tx power */
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_MAX =
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_SCALE_AFTER_LAST - 1
+};
+
+/**
+ * enum qca_vendor_attr_txpower_decr_db - Attributes for TX power decrease
+ *
+ * These attributes are used with QCA_NL80211_VENDOR_SUBCMD_SET_TXPOWER_DECR_DB.
+ */
+enum qca_vendor_attr_txpower_decr_db {
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_INVALID,
+ /* 8-bit unsigned value to indicate the reduction of TX power in dB for
+ * a virtual interface. */
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_MAX =
+ QCA_WLAN_VENDOR_ATTR_TXPOWER_DECR_DB_AFTER_LAST - 1
+};
+
+/* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
+ * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
+ */
+enum qca_wlan_vendor_attr_config {
+ QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID,
+ /* Unsigned 32-bit value to set the DTIM period.
+ * Whether the wifi chipset wakes at every dtim beacon or a multiple of
+ * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3
+ * DTIM beacons.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM,
+ /* Unsigned 32-bit value to set the wifi_iface stats averaging factor
+ * used to calculate statistics like average the TSF offset or average
+ * number of frame leaked.
+ * For instance, upon Beacon frame reception:
+ * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000
+ * For instance, when evaluating leaky APs:
+ * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR,
+ /* Unsigned 32-bit value to configure guard time, i.e., when
+ * implementing IEEE power management based on frame control PM bit, how
+ * long the driver waits before shutting down the radio and after
+ * receiving an ACK frame for a Data frame with PM bit set.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME,
+ /* Unsigned 32-bit value to change the FTM capability dynamically */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT,
+ /* Unsigned 16-bit value to configure maximum TX rate dynamically */
+ QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE,
+ /* Unsigned 32-bit value to configure the number of continuous
+ * Beacon Miss which shall be used by the firmware to penalize
+ * the RSSI.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS,
+ /* Unsigned 8-bit value to configure the channel avoidance indication
+ * behavior. Firmware to send only one indication and ignore duplicate
+ * indications when set to avoid multiple Apps wakeups.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND,
+ /* 8-bit unsigned value to configure the maximum TX MPDU for
+ * aggregation. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION,
+ /* 8-bit unsigned value to configure the maximum RX MPDU for
+ * aggregation. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION,
+ /* 8-bit unsigned value to configure the Non aggregrate/11g sw
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY,
+ /* 8-bit unsigned value to configure the aggregrate sw
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY,
+ /* 8-bit unsigned value to configure the MGMT frame
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY,
+ /* 8-bit unsigned value to configure the CTRL frame
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY,
+ /* 8-bit unsigned value to configure the propagation delay for
+ * 2G/5G band (0~63, units in us) */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY,
+ /* Unsigned 32-bit value to configure the number of unicast TX fail
+ * packet count. The peer is disconnected once this threshold is
+ * reached. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT,
+ /* Attribute used to set scan default IEs to the driver.
+ *
+ * These IEs can be used by scan operations that will be initiated by
+ * the driver/firmware.
+ *
+ * For further scan requests coming to the driver, these IEs should be
+ * merged with the IEs received along with scan request coming to the
+ * driver. If a particular IE is present in the scan default IEs but not
+ * present in the scan request, then that IE should be added to the IEs
+ * sent in the Probe Request frames for that scan request. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES,
+ /* Unsigned 32-bit attribute for generic commands */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND,
+ /* Unsigned 32-bit value attribute for generic commands */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE,
+ /* Unsigned 32-bit data attribute for generic command response */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA,
+ /* Unsigned 32-bit length attribute for
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH,
+ /* Unsigned 32-bit flags attribute for
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS,
+ /* Unsigned 32-bit, defining the access policy.
+ * See enum qca_access_policy. Used with
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY,
+ /* Sets the list of full set of IEs for which a specific access policy
+ * has to be applied. Used along with
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
+ * Zero length payload can be used to clear this access constraint. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST,
+ /* Unsigned 32-bit, specifies the interface index (netdev) for which the
+ * corresponding configurations are applied. If the interface index is
+ * not specified, the configurations are attributed to the respective
+ * wiphy. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX,
+ /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_MAX =
+ QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration
+ */
+enum qca_wlan_vendor_attr_sap_config {
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0,
+ /* 1 - reserved for QCA */
+ /* List of frequencies on which AP is expected to operate.
+ * This is irrespective of ACS configuration. This list is a priority
+ * based one and is looked for before the AP is created to ensure the
+ * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in
+ * the system.
+ */
+ QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2,
+
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX =
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
+ * conditional channel switch
+ */
+enum qca_wlan_vendor_attr_sap_conditional_chan_switch {
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0,
+ /* Priority based frequency list (an array of u32 values in host byte
+ * order) */
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1,
+ /* Status of the conditional switch (u32).
+ * 0: Success, Non-zero: Failure
+ */
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2,
+
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX =
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_gpio_attr - Parameters for GPIO configuration
+ */
+enum qca_wlan_gpio_attr {
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0,
+ /* Unsigned 32-bit attribute for GPIO command */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND,
+ /* Unsigned 32-bit attribute for GPIO PIN number to configure */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM,
+ /* Unsigned 32-bit attribute for GPIO value to configure */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE,
+ /* Unsigned 32-bit attribute for GPIO pull type */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE,
+ /* Unsigned 32-bit attribute for GPIO interrupt mode */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST,
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
+ */
+enum qca_wlan_vendor_attr_get_hw_capability {
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID,
+ /* Antenna isolation
+ * An attribute used in the response.
+ * The content of this attribute is encoded in a byte array. Each byte
+ * value is an antenna isolation value. The array length is the number
+ * of antennas.
+ */
+ QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION,
+ /* Request HW capability
+ * An attribute used in the request.
+ * The content of this attribute is a u32 array for one or more of
+ * hardware capabilities (attribute IDs) that are being requested. Each
+ * u32 value has a value from this
+ * enum qca_wlan_vendor_attr_get_hw_capability
+ * identifying which capabilities are requested.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX =
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
+ * offload which is an extension for LL_STATS.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
+ * If MAC counters do not exceed the threshold, FW will report monitored
+ * link layer counters periodically as this setting. The first report is
+ * always triggered by this timer.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
+ * For each MAC layer counter, FW holds two copies. One is the current value.
+ * The other is the last report. Once a current counter's increment is larger
+ * than the threshold, FW will indicate that counter to host even if the
+ * monitoring timer does not expire.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
+ * failure code.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
+ * 1: TX packet discarded
+ * 2: No ACK
+ * 3: Postpone
+ */
+enum qca_wlan_vendor_attr_ll_stats_ext {
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0,
+
+ /* Attributes for configurations */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD,
+
+ /* Attributes for events */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG,
+
+ /* TX failure event */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS,
+
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX =
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1