+/* Attributes for data used by
+ * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
+ * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
+ */
+enum qca_wlan_vendor_attr_config {
+ QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID,
+ /* Unsigned 32-bit value to set the DTIM period.
+ * Whether the wifi chipset wakes at every dtim beacon or a multiple of
+ * the DTIM period. If DTIM is set to 3, the STA shall wake up every 3
+ * DTIM beacons.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_DYNAMIC_DTIM,
+ /* Unsigned 32-bit value to set the wifi_iface stats averaging factor
+ * used to calculate statistics like average the TSF offset or average
+ * number of frame leaked.
+ * For instance, upon Beacon frame reception:
+ * current_avg = ((beacon_TSF - TBTT) * factor + previous_avg * (0x10000 - factor) ) / 0x10000
+ * For instance, when evaluating leaky APs:
+ * current_avg = ((num frame received within guard time) * factor + previous_avg * (0x10000 - factor)) / 0x10000
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_STATS_AVG_FACTOR,
+ /* Unsigned 32-bit value to configure guard time, i.e., when
+ * implementing IEEE power management based on frame control PM bit, how
+ * long the driver waits before shutting down the radio and after
+ * receiving an ACK frame for a Data frame with PM bit set.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GUARD_TIME,
+ /* Unsigned 32-bit value to change the FTM capability dynamically */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_FINE_TIME_MEASUREMENT,
+ /* Unsigned 16-bit value to configure maximum TX rate dynamically */
+ QCA_WLAN_VENDOR_ATTR_CONF_TX_RATE,
+ /* Unsigned 32-bit value to configure the number of continuous
+ * Beacon Miss which shall be used by the firmware to penalize
+ * the RSSI.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PENALIZE_AFTER_NCONS_BEACON_MISS,
+ /* Unsigned 8-bit value to configure the channel avoidance indication
+ * behavior. Firmware to send only one indication and ignore duplicate
+ * indications when set to avoid multiple Apps wakeups.
+ */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_CHANNEL_AVOIDANCE_IND,
+ /* 8-bit unsigned value to configure the maximum TX MPDU for
+ * aggregation. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_MPDU_AGGREGATION,
+ /* 8-bit unsigned value to configure the maximum RX MPDU for
+ * aggregation. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION,
+ /* 8-bit unsigned value to configure the Non aggregrate/11g sw
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY,
+ /* 8-bit unsigned value to configure the aggregrate sw
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY,
+ /* 8-bit unsigned value to configure the MGMT frame
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY,
+ /* 8-bit unsigned value to configure the CTRL frame
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY,
+ /* 8-bit unsigned value to configure the propagation delay for
+ * 2G/5G band (0~63, units in us) */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY,
+ /* Unsigned 32-bit value to configure the number of unicast TX fail
+ * packet count. The peer is disconnected once this threshold is
+ * reached. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT,
+ /* Attribute used to set scan default IEs to the driver.
+ *
+ * These IEs can be used by scan operations that will be initiated by
+ * the driver/firmware.
+ *
+ * For further scan requests coming to the driver, these IEs should be
+ * merged with the IEs received along with scan request coming to the
+ * driver. If a particular IE is present in the scan default IEs but not
+ * present in the scan request, then that IE should be added to the IEs
+ * sent in the Probe Request frames for that scan request. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES,
+ /* Unsigned 32-bit attribute for generic commands */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND,
+ /* Unsigned 32-bit value attribute for generic commands */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE,
+ /* Unsigned 32-bit data attribute for generic command response */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA,
+ /* Unsigned 32-bit length attribute for
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH,
+ /* Unsigned 32-bit flags attribute for
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS,
+ /* Unsigned 32-bit, defining the access policy.
+ * See enum qca_access_policy. Used with
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY,
+ /* Sets the list of full set of IEs for which a specific access policy
+ * has to be applied. Used along with
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
+ * Zero length payload can be used to clear this access constraint. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST,
+ /* Unsigned 32-bit, specifies the interface index (netdev) for which the
+ * corresponding configurations are applied. If the interface index is
+ * not specified, the configurations are attributed to the respective
+ * wiphy. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX,
+ /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_CONFIG_MAX =
+ QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_sap_config - Parameters for AP configuration
+ */
+enum qca_wlan_vendor_attr_sap_config {
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_INVALID = 0,
+ /* 1 - reserved for QCA */
+ /* List of frequencies on which AP is expected to operate.
+ * This is irrespective of ACS configuration. This list is a priority
+ * based one and is looked for before the AP is created to ensure the
+ * best concurrency sessions (avoid MCC and use DBS/SCC) co-exist in
+ * the system.
+ */
+ QCA_WLAN_VENDOR_ATTR_SAP_MANDATORY_FREQUENCY_LIST = 2,
+
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_MAX =
+ QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
+ * conditional channel switch
+ */
+enum qca_wlan_vendor_attr_sap_conditional_chan_switch {
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0,
+ /* Priority based frequency list (an array of u32 values in host byte
+ * order) */
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1,
+ /* Status of the conditional switch (u32).
+ * 0: Success, Non-zero: Failure
+ */
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2,
+
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX =
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_gpio_attr - Parameters for GPIO configuration
+ */
+enum qca_wlan_gpio_attr {
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0,
+ /* Unsigned 32-bit attribute for GPIO command */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND,
+ /* Unsigned 32-bit attribute for GPIO PIN number to configure */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM,
+ /* Unsigned 32-bit attribute for GPIO value to configure */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE,
+ /* Unsigned 32-bit attribute for GPIO pull type */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE,
+ /* Unsigned 32-bit attribute for GPIO interrupt mode */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST,
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
+ */
+enum qca_wlan_vendor_attr_get_hw_capability {
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID,
+ /* Antenna isolation
+ * An attribute used in the response.
+ * The content of this attribute is encoded in a byte array. Each byte
+ * value is an antenna isolation value. The array length is the number
+ * of antennas.
+ */
+ QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION,
+ /* Request HW capability
+ * An attribute used in the request.
+ * The content of this attribute is a u32 array for one or more of
+ * hardware capabilities (attribute IDs) that are being requested. Each
+ * u32 value has a value from this
+ * enum qca_wlan_vendor_attr_get_hw_capability
+ * identifying which capabilities are requested.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX =
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
+ * offload which is an extension for LL_STATS.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
+ * If MAC counters do not exceed the threshold, FW will report monitored
+ * link layer counters periodically as this setting. The first report is
+ * always triggered by this timer.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
+ * For each MAC layer counter, FW holds two copies. One is the current value.
+ * The other is the last report. Once a current counter's increment is larger
+ * than the threshold, FW will indicate that counter to host even if the
+ * monitoring timer does not expire.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
+ * failure code.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
+ * 1: TX packet discarded
+ * 2: No ACK
+ * 3: Postpone
+ */
+enum qca_wlan_vendor_attr_ll_stats_ext {
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0,
+
+ /* Attributes for configurations */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD,
+
+ /* Attributes for events */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG,
+
+ /* TX failure event */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS,
+
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX =
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1
+};
+