+# Passphrase length (8..63) for P2P GO
+#
+# This parameter controls the length of the random passphrase that is
+# generated at the GO. Default: 8.
+#p2p_passphrase_len=8
+
+# Extra delay between concurrent P2P search iterations
+#
+# This value adds extra delay in milliseconds between concurrent search
+# iterations to make p2p_find friendlier to concurrent operations by avoiding
+# it from taking 100% of radio resources. The default value is 500 ms.
+#p2p_search_delay=500
+
+# Opportunistic Key Caching (also known as Proactive Key Caching) default
+# This parameter can be used to set the default behavior for the
+# proactive_key_caching parameter. By default, OKC is disabled unless enabled
+# with the global okc=1 parameter or with the per-network
+# proactive_key_caching=1 parameter. With okc=1, OKC is enabled by default, but
+# can be disabled with per-network proactive_key_caching=0 parameter.
+#okc=0
+
+# Protected Management Frames default
+# This parameter can be used to set the default behavior for the ieee80211w
+# parameter for RSN networks. By default, PMF is disabled unless enabled with
+# the global pmf=1/2 parameter or with the per-network ieee80211w=1/2 parameter.
+# With pmf=1/2, PMF is enabled/required by default, but can be disabled with the
+# per-network ieee80211w parameter. This global default value does not apply
+# for non-RSN networks (key_mgmt=NONE) since PMF is available only when using
+# RSN.
+#pmf=0
+
+# Enabled SAE finite cyclic groups in preference order
+# By default (if this parameter is not set), the mandatory group 19 (ECC group
+# defined over a 256-bit prime order field) is preferred, but other groups are
+# also enabled. If this parameter is set, the groups will be tried in the
+# indicated order. The group values are listed in the IANA registry:
+# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9
+#sae_groups=21 20 19 26 25
+
+# Default value for DTIM period (if not overridden in network block)
+#dtim_period=2
+
+# Default value for Beacon interval (if not overridden in network block)
+#beacon_int=100
+
+# Additional vendor specific elements for Beacon and Probe Response frames
+# This parameter can be used to add additional vendor specific element(s) into
+# the end of the Beacon and Probe Response frames. The format for these
+# element(s) is a hexdump of the raw information elements (id+len+payload for
+# one or more elements). This is used in AP and P2P GO modes.
+#ap_vendor_elements=dd0411223301
+
+# Ignore scan results older than request
+#
+# The driver may have a cache of scan results that makes it return
+# information that is older than our scan trigger. This parameter can
+# be used to configure such old information to be ignored instead of
+# allowing it to update the internal BSS table.
+#ignore_old_scan_res=0
+
+# scan_cur_freq: Whether to scan only the current frequency
+# 0: Scan all available frequencies. (Default)
+# 1: Scan current operating frequency if another VIF on the same radio
+# is already associated.
+
+# MAC address policy default
+# 0 = use permanent MAC address
+# 1 = use random MAC address for each ESS connection
+# 2 = like 1, but maintain OUI (with local admin bit set)
+#
+# By default, permanent MAC address is used unless policy is changed by
+# the per-network mac_addr parameter. Global mac_addr=1 can be used to
+# change this default behavior.
+#mac_addr=0
+
+# Lifetime of random MAC address in seconds (default: 60)
+#rand_addr_lifetime=60
+
+# MAC address policy for pre-association operations (scanning, ANQP)
+# 0 = use permanent MAC address
+# 1 = use random MAC address
+# 2 = like 1, but maintain OUI (with local admin bit set)
+#preassoc_mac_addr=0