# management frames); ath0 for madwifi
interface=wlan0
-# In case of madwifi and nl80211 driver interfaces, an additional configuration
-# parameter, bridge, must be used to notify hostapd if the interface is
-# included in a bridge. This parameter is not used with Host AP driver.
+# In case of madwifi, atheros, and nl80211 driver interfaces, an additional
+# configuration parameter, bridge, may be used to notify hostapd if the
+# interface is included in a bridge. This parameter is not used with Host AP
+# driver. If the bridge parameter is not set, the drivers will automatically
+# figure out the bridge interface (assuming sysfs is enabled and mounted to
+# /sys) and this parameter may not be needed.
+#
+# For nl80211, this parameter can be used to request the AP interface to be
+# added to the bridge automatically (brctl may refuse to do this before hostapd
+# has been started to change the interface mode). If needed, the bridge
+# interface is also created.
#bridge=br0
-# Driver interface type (hostap/wired/madwifi/prism54/test/none/nl80211/bsd);
+# Driver interface type (hostap/wired/madwifi/test/none/nl80211/bsd);
# default: hostap). nl80211 is used with all Linux mac80211 drivers.
# Use driver=none if building hostapd as a standalone RADIUS server that does
# not control any wireless/wired driver.
#
wmm_enabled=1
#
+# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD]
+# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver)
+#uapsd_advertisement_enabled=1
+#
# Low priority / AC_BK = background
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
# default: 300 (i.e., 5 minutes)
#ap_max_inactivity=300
-# Enable/disable internal bridge for packets between associated stations.
-#
-# When IEEE 802.11 is used in managed mode, packets are usually send through
-# the AP even if they are from a wireless station to another wireless station.
-# This functionality requires that the AP has a bridge functionality that sends
-# frames back to the same interface if their destination is another associated
-# station. In addition, broadcast/multicast frames from wireless stations will
-# be sent both to the host system net stack (e.g., to eventually wired network)
-# and back to the wireless interface.
-#
-# The internal bridge is implemented within the wireless kernel module and it
-# bypasses kernel filtering (netfilter/iptables/ebtables). If direct
-# communication between the stations needs to be prevented, the internal
-# bridge can be disabled by setting bridge_packets=0.
-#
-# Note: If this variable is not included in hostapd.conf, hostapd does not
-# change the configuration and iwpriv can be used to set the value with
-# 'iwpriv wlan# param 10 0' command. If the variable is in hostapd.conf,
-# hostapd will override possible iwpriv configuration whenever configuration
-# file is reloaded.
-#
-# default: do not control from hostapd (80211.o defaults to 1=enabled)
-#bridge_packets=1
-
# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to
# remain asleep). Default: 65535 (no limit apart from field size)
#max_listen_interval=100
+# WDS (4-address frame) mode with per-station virtual interfaces
+# (only supported with driver=nl80211)
+# This mode allows associated stations to use 4-address frames to allow layer 2
+# bridging to be used.
+#wds_sta=1
+
##### IEEE 802.11n related configuration ######################################
# ieee80211n: Whether IEEE 802.11n (HT) is enabled
# And so on.. One line per R0KH.
# List of R1KHs in the same Mobility Domain
-# format: <MAC address> <R0KH-ID> <128-bit key as hex string>
+# format: <MAC address> <R1KH-ID> <128-bit key as hex string>
# This list is used to map R1KH-ID to a destination MAC address when sending
# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD
# that can request PMK-R1 keys.
# Config Methods
# List of the supported configuration methods
+# Available methods: usba ethernet label display ext_nfc_token int_nfc_token
+# nfc_interface push_button keypad
#config_methods=label display push_button keypad
# Access point PIN for initial configuration and adding Registrars