Extend the range of values for the RTS threshold

[mech_eap.git] / hostapd / hostapd.conf

diff --git a/hostapd/hostapd.conf b/hostapd/hostapd.conf
index c15cc44..5f4220d 100644 (file)
--- a/hostapd/hostapd.conf
+++ b/hostapd/hostapd.conf
@@ -173,7 +173,7 @@ channel=1
 # Channel list restriction. This option allows hostapd to select one of the
 # provided channels when a channel should be automatically selected.
 # Channel list can be provided as range using hyphen ('-') or individual
-# channels can be specified by space (' ') seperated values
+# channels can be specified by space (' ') separated values
 # Default: all channels allowed in selected hw_mode
 #chanlist=100 104 108 112 116
 #chanlist=1 6 11-13
@@ -192,10 +192,10 @@ dtim_period=2
 # (default: 2007)
 max_num_sta=255
 
-# RTS/CTS threshold; 2347 = disabled (default); range 0..2347
+# RTS/CTS threshold; -1 = disabled (default); range -1..65535
 # If this field is not included in hostapd.conf, hostapd will not control
 # RTS threshold and 'iwconfig wlan# rts <val>' can be used to set it.
-rts_threshold=2347
+rts_threshold=-1
 
 # Fragmentation threshold; 2346 = disabled (default); range 256..2346
 # If this field is not included in hostapd.conf, hostapd will not control
@@ -267,7 +267,14 @@ auth_algs=3
 #     requests for broadcast SSID
 ignore_broadcast_ssid=0
 
-# Additional vendor specfic elements for Beacon and Probe Response frames
+# Do not reply to broadcast Probe Request frames from unassociated STA if there
+# is no room for additional stations (max_num_sta). This can be used to
+# discourage a STA from trying to associate with this AP if the association
+# would be rejected due to maximum STA limit.
+# Default: 0 (disabled)
+#no_probe_resp_if_max_sta=0
+
+# Additional vendor specific elements for Beacon and Probe Response frames
 # This parameter can be used to add additional vendor specific element(s) into
 # the end of the Beacon and Probe Response frames. The format for these
 # element(s) is a hexdump of the raw information elements (id+len+payload for
@@ -605,9 +612,9 @@ wmm_ac_vo_acm=0
 # VHT TXOP PS: [VHT-TXOP-PS]
 # Indicates whether or not the AP supports VHT TXOP Power Save Mode
 #  or whether or not the STA is in VHT TXOP Power Save mode
-# 0 = VHT AP doesnt support VHT TXOP PS mode (OR) VHT Sta not in VHT TXOP PS
+# 0 = VHT AP doesn't support VHT TXOP PS mode (OR) VHT STA not in VHT TXOP PS
 #  mode
-# 1 = VHT AP supports VHT TXOP PS mode (OR) VHT Sta is in VHT TXOP power save
+# 1 = VHT AP supports VHT TXOP PS mode (OR) VHT STA is in VHT TXOP power save
 #  mode
 #
 # +HTC-VHT Capable: [HTC-VHT]
@@ -1684,6 +1691,17 @@ own_ip_addr=127.0.0.1
 # username/password
 #nai_realm=0,example.org,13[5:6],21[2:4][5:7]
 
+# Arbitrary ANQP-element configuration
+# Additional ANQP-elements with arbitrary values can be defined by specifying
+# their contents in raw format as a hexdump of the payload. Note that these
+# values will override ANQP-element contents that may have been specified in the
+# more higher layer configuration parameters listed above.
+# format: anqp_elem=<InfoID>:<hexdump of payload>
+# For example, AP Geospatial Location ANQP-element with unknown location:
+#anqp_elem=265:0000
+# For example, AP Civic Location ANQP-element with unknown location:
+#anqp_elem=266:000000
+
 # QoS Map Set configuration
 #
 # Comma delimited QoS Map Set in decimal values