# included in a bridge. This parameter is not used with Host AP driver.
#bridge=br0
-# Driver interface type (hostap/wired/madwifi/prism54/test/none/nl80211/bsd);
+# Driver interface type (hostap/wired/madwifi/test/none/nl80211/bsd);
# default: hostap). nl80211 is used with all Linux mac80211 drivers.
# Use driver=none if building hostapd as a standalone RADIUS server that does
# not control any wireless/wired driver.
# default: 300 (i.e., 5 minutes)
#ap_max_inactivity=300
-# Enable/disable internal bridge for packets between associated stations.
-#
-# When IEEE 802.11 is used in managed mode, packets are usually send through
-# the AP even if they are from a wireless station to another wireless station.
-# This functionality requires that the AP has a bridge functionality that sends
-# frames back to the same interface if their destination is another associated
-# station. In addition, broadcast/multicast frames from wireless stations will
-# be sent both to the host system net stack (e.g., to eventually wired network)
-# and back to the wireless interface.
-#
-# The internal bridge is implemented within the wireless kernel module and it
-# bypasses kernel filtering (netfilter/iptables/ebtables). If direct
-# communication between the stations needs to be prevented, the internal
-# bridge can be disabled by setting bridge_packets=0.
-#
-# Note: If this variable is not included in hostapd.conf, hostapd does not
-# change the configuration and iwpriv can be used to set the value with
-# 'iwpriv wlan# param 10 0' command. If the variable is in hostapd.conf,
-# hostapd will override possible iwpriv configuration whenever configuration
-# file is reloaded.
-#
-# default: do not control from hostapd (80211.o defaults to 1=enabled)
-#bridge_packets=1
-
# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to
# remain asleep). Default: 65535 (no limit apart from field size)
#max_listen_interval=100
# EAP-FAST authority identity (A-ID)
# A-ID indicates the identity of the authority that issues PACs. The A-ID
# should be unique across all issuing servers. In theory, this is a variable
-# length field, but due to some existing implementations required A-ID to be
+# length field, but due to some existing implementations requiring A-ID to be
# 16 octets in length, it is strongly recommended to use that length for the
-# field to provided interoperability with deployed peer implementation. This
+# field to provid interoperability with deployed peer implementations. This
# field is configured in hex format.
#eap_fast_a_id=101112131415161718191a1b1c1d1e1f
# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived
#pmk_r1_push=1
-##### Passive scanning ########################################################
-# Scan different channels every N seconds. 0 = disable passive scanning.
-#passive_scan_interval=60
-
-# Listen N usecs on each channel when doing passive scanning.
-# This value plus the time needed for changing channels should be less than
-# 32 milliseconds (i.e. 32000 usec) to avoid interruptions to normal
-# operations. Time needed for channel changing varies based on the used wlan
-# hardware.
-# default: disabled (0)
-#passive_scan_listen=10000
-
-# Passive scanning mode:
-# 0 = scan all supported modes (802.11a/b/g/Turbo) (default)
-# 1 = scan only the mode that is currently used for normal operations
-#passive_scan_mode=1
-
-# Maximum number of entries kept in AP table (either for passive scanning or
-# for detecting Overlapping Legacy BSS Condition). The oldest entry will be
+##### Neighbor table ##########################################################
+# Maximum number of entries kept in AP table (either for neigbor table or for
+# detecting Overlapping Legacy BSS Condition). The oldest entry will be
# removed when adding a new entry that would make the list grow over this
-# limit. Note! Wi-Fi certification for IEEE 802.11g requires that OLBC is
+# limit. Note! WFA certification for IEEE 802.11g requires that OLBC is
# enabled, so this field should not be set to 0 when using IEEE 802.11g.
# default: 255
#ap_table_max_size=255
# Config Methods
# List of the supported configuration methods
+# Available methods: usba ethernet label display ext_nfc_token int_nfc_token
+# nfc_interface push_button keypad
#config_methods=label display push_button keypad
# Access point PIN for initial configuration and adding Registrars
# hostapd will generate BSSID mask based on the BSSIDs that are
# configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is
# not the case, the MAC address of the radio must be changed before starting
-# hostapd (ifconfig wlan0 hw ether <MAC addr>).
+# hostapd (ifconfig wlan0 hw ether <MAC addr>). If a BSSID is configured for
+# every secondary BSS, this limitation is not applied at hostapd and other
+# masks may be used if the driver supports them (e.g., swap the locally
+# administered bit)
#
# BSSIDs are assigned in order to each BSS, unless an explicit BSSID is
# specified using the 'bssid' parameter.
projects / libeap.git / blobdiff