# (data0 is the highest priority queue)
# parameters:
# aifs: AIFS (default 2)
-# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023)
-# cwmax: cwMax (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023); cwMax >= cwMin
+# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023, 2047, 4095, 8191,
+# 16383, 32767)
+# cwmax: cwMax (same values as cwMin, cwMax >= cwMin)
# burst: maximum length (in milliseconds with precision of up to 0.1 ms) for
# bursting
#
# note - txop_limit is in units of 32microseconds
# note - acm is admission control mandatory flag. 0 = admission control not
# required, 1 = mandatory
-# note - here cwMin and cmMax are in exponent form. the actual cw value used
-# will be (2^n)-1 where n is the value given here
+# note - Here cwMin and cmMax are in exponent form. The actual cw value used
+# will be (2^n)-1 where n is the value given here. The allowed range for these
+# wmm_ac_??_{cwmin,cwmax} is 0..15 with cwmax >= cwmin.
#
wmm_enabled=1
#
# 0 = Not supported (default)
# 1 = Supported
#
-# Compressed Steering Number of Beamformer Antennas Supported: [BF-ANTENNA-2]
+# Compressed Steering Number of Beamformer Antennas Supported:
+# [BF-ANTENNA-2] [BF-ANTENNA-3] [BF-ANTENNA-4]
# Beamformee's capability indicating the maximum number of beamformer
# antennas the beamformee can support when sending compressed beamforming
# feedback
# If SU beamformer capable, set to maximum value minus 1
# else reserved (default)
#
-# Number of Sounding Dimensions: [SOUNDING-DIMENSION-2]
+# Number of Sounding Dimensions:
+# [SOUNDING-DIMENSION-2] [SOUNDING-DIMENSION-3] [SOUNDING-DIMENSION-4]
# Beamformer's capability indicating the maximum value of the NUM_STS parameter
# in the TXVECTOR of a VHT NDP
# If SU beamformer capable, set to maximum value minus 1
# 2 = check all CRLs in the certificate path
#check_crl=1
+# TLS Session Lifetime in seconds
+# This can be used to allow TLS sessions to be cached and resumed with an
+# abbreviated handshake when using EAP-TLS/TTLS/PEAP.
+# (default: 0 = session caching and resumption disabled)
+#tls_session_lifetime=3600
+
# Cached OCSP stapling response (DER encoded)
# If set, this file is sent as a certificate status response by the EAP server
# if the EAP peer requests certificate status in the ClientHello message.
# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived
#pmk_r1_push=1
+# Whether to enable FT-over-DS
+# 0 = FT-over-DS disabled
+# 1 = FT-over-DS enabled (default)
+#ft_over_ds=1
+
##### Neighbor table ##########################################################
# Maximum number of entries kept in AP table (either for neigbor table or for
# detecting Overlapping Legacy BSS Condition). The oldest entry will be
# default: 60
#ap_table_expiration_time=3600
+# Maximum number of stations to track on the operating channel
+# This can be used to detect dualband capable stations before they have
+# associated, e.g., to provide guidance on which colocated BSS to use.
+# Default: 0 (disabled)
+#track_sta_max_num=100
+
+# Maximum age of a station tracking entry in seconds
+# Default: 180
+#track_sta_max_age=180
+
+# Do not reply to group-addressed Probe Request from a station that was seen on
+# another radio.
+# Default: Disabled
+#
+# This can be used with enabled track_sta_max_num configuration on another
+# interface controlled by the same hostapd process to restrict Probe Request
+# frame handling from replying to group-addressed Probe Request frames from a
+# station that has been detected to be capable of operating on another band,
+# e.g., to try to reduce likelihood of the station selecting a 2.4 GHz BSS when
+# the AP operates both a 2.4 GHz and 5 GHz BSS concurrently.
+#
+# Note: Enabling this can cause connectivity issues and increase latency for
+# discovering the AP.
+#no_probe_resp_if_seen_on=wlan1
+
+# Reject authentication from a station that was seen on another radio.
+# Default: Disabled
+#
+# This can be used with enabled track_sta_max_num configuration on another
+# interface controlled by the same hostapd process to reject authentication
+# attempts from a station that has been detected to be capable of operating on
+# another band, e.g., to try to reduce likelihood of the station selecting a
+# 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz BSS concurrently.
+#
+# Note: Enabling this can cause connectivity issues and increase latency for
+# connecting with the AP.
+#no_auth_if_seen_on=wlan1
##### Wi-Fi Protected Setup (WPS) #############################################
#
#osu_server_uri=...
+##### Fast Session Transfer (FST) support #####################################
+#
+# The options in this section are only available when the build configuration
+# option CONFIG_FST is set while compiling hostapd. They allow this interface
+# to be a part of FST setup.
+#
+# FST is the transfer of a session from a channel to another channel, in the
+# same or different frequency bands.
+#
+# For detals, see IEEE Std 802.11ad-2012.
+
+# Identifier of an FST Group the interface belongs to.
+#fst_group_id=bond0
+
+# Interface priority within the FST Group.
+# Announcing a higher priority for an interface means declaring it more
+# preferable for FST switch.
+# fst_priority is in 1..255 range with 1 being the lowest priority.
+#fst_priority=100
+
+# Default LLT value for this interface in milliseconds. The value used in case
+# no value provided during session setup. Default is 50 ms.
+# fst_llt is in 1..4294967 range (due to spec limitation, see 10.32.2.2
+# Transitioning between states).
+#fst_llt=100
+
##### TESTING OPTIONS #########################################################
#
# The options in this section are only available when the build configuration
projects / mech_eap.git / blobdiff