# documented in that "man" page. They are only documented here,
# in the comments.
#
-# As of 2.0.0, FreeRADIUS supports a simple processing language
-# in the "authorize", "authenticate", "accounting", etc. sections.
-# See "man unlang" for details.
+# The "unlang" policy language can be used to create complex
+# if / else policies. See "man unlang" for details.
#
prefix = @prefix@
#
pidfile = ${run_dir}/${name}.pid
+#
+# correct_escapes: use correct backslash escaping
+#
+# Prior to version 3.0.5, the handling of backslashes was a little
+# awkward, i.e. "wrong". In some cases, to get one backslash into
+# a regex, you had to put 4 in the config files.
+#
+# Version 3.0.5 fixes that. However, for backwards compatibility,
+# the new method of escaping is DISABLED BY DEFAULT. This means
+# that upgrading to 3.0.5 won't break your configuration.
+#
+# If you don't have double backslashes (i.e. \\) in your configuration,
+# this won't matter to you. If you do have them, fix that to use only
+# one backslash, and then set "correct_escapes = true".
+#
+# You can check for this by doing:
+#
+# $ grep '\\\\' $(find raddb -type f -print)
+#
+correct_escapes = true
+
+# panic_action: Command to execute if the server dies unexpectedly.
+#
+# FOR PRODUCTION SYSTEMS, ACTIONS SHOULD ALWAYS EXIT.
+# AN INTERACTIVE ACTION MEANS THE SERVER IS NOT RESPONDING TO REQUESTS.
+# AN INTERACTICE ACTION MEANS THE SERVER WILL NOT RESTART.
+#
+# THE SERVER MUST NOT BE ALLOWED EXECUTE UNTRUSTED PANIC ACTION CODE
+# PATTACH CAN BE USED AS AN ATTACK VECTOR.
+#
+# The panic action is a command which will be executed if the server
+# receives a fatal, non user generated signal, i.e. SIGSEGV, SIGBUS,
+# SIGABRT or SIGFPE.
+#
+# This can be used to start an interactive debugging session so
+# that information regarding the current state of the server can
+# be acquired.
+#
+# The following string substitutions are available:
+# - %e The currently executing program e.g. /sbin/radiusd
+# - %p The PID of the currently executing program e.g. 12345
+#
+# Standard ${} substitutions are also allowed.
+#
+# An example panic action for opening an interactive session in GDB would be:
+#
+#panic_action = "gdb %e %p"
+#
+# Again, don't use that on a production system.
+#
+# An example panic action for opening an automated session in GDB would be:
+#
+#panic_action = "gdb -silent -x ${raddbdir}/panic.gdb %e %p 2>&1 | tee ${logdir}/gdb-${name}-%p.log"
+#
+# That command can be used on a production system.
+#
+
# max_request_time: The maximum time (in seconds) to handle a request.
#
# Requests which take more time than this to process may be killed, and
#
# Useful range of values: 256 to infinity
#
-max_requests = 1024
+max_requests = 16384
# hostname_lookups: Log the names of clients or just their IP addresses
# e.g., www.freeradius.org (on) or 206.47.27.232 (off).
file = ${logdir}/radius.log
#
- # If this configuration parameter is set, then log messages for
- # a *request* go to this file, rather than to radius.log.
- #
- # i.e. This is a log file per request, once the server has accepted
- # the request as being from a valid client. Messages that are
- # not associated with a request still go to radius.log.
- #
- # Not all log messages in the server core have been updated to use
- # this new internal API. As a result, some messages will still
- # go to radius.log. Please submit patches to fix this behavior.
- #
- # The file name is expanded dynamically. You should ONLY user
- # server-side attributes for the filename (e.g. things you control).
- # Using this feature MAY also slow down the server substantially,
- # especially if you do thinks like SQL calls as part of the
- # expansion of the filename.
- #
- # The name of the log file should use attributes that don't change
- # over the lifetime of a request, such as User-Name,
- # Virtual-Server or Packet-Src-IP-Address. Otherwise, the log
- # messages will be distributed over multiple files.
- #
- # Logging can be enabled for an individual request by a special
- # dynamic expansion macro: %{debug: 1}, where the debug level
- # for this request is set to '1' (or 2, 3, etc.). e.g.
- #
- # ...
- # update control {
- # Tmp-String-0 = "%{debug:1}"
- # }
- # ...
- #
- # The attribute that the value is assigned to is unimportant,
- # and should be a "throw-away" attribute with no side effects.
- #
- #requests = ${logdir}/radiusd-%{%{Virtual-Server}:-DEFAULT}-%Y%m%d.log
-
- #
# Which syslog facility to use, if ${destination} == "syslog"
#
# The exact values permitted here are OS-dependent. You probably
#
# msg_goodpass = ""
# msg_badpass = ""
+
+ # The message when the user exceeds the Simultaneous-Use limit.
+ #
+ msg_denied = "You are already logged in - access denied"
}
# The program to execute to do concurrency checks.
# rejects will be sent at 'cleanup_delay' time, when the request
# is deleted from the internal cache of requests.
#
+ # As of Version 3.0.5, "reject_delay" has sub-second resolution.
+ # e.g. "reject_delay = 1.4" seconds is possible.
+ #
# Useful ranges: 1 to 5
reject_delay = 1
# See also raddb/sites-available/status
#
status_server = yes
+
+@openssl_version_check_config@
}
# PROXY CONFIGURATION
# CLIENTS CONFIGURATION
#
-# Client configuration is defined in "clients.conf".
+# Client configuration is defined in "clients.conf".
#
# The 'clients.conf' file contains all of the information from the old
auto_limit_acct = no
}
+######################################################################
+#
+# SNMP notifications. Uncomment the following line to enable
+# snmptraps. Note that you MUST also configure the full path
+# to the "snmptrap" command in the "trigger.conf" file.
+#
+#$INCLUDE trigger.conf
+
# MODULE CONFIGURATION
#
# The names and configuration of each module is located in this section.
# lines, and list "redundant_sql" in the authorize and
# accounting sections.
#
+ # The "virtual" module defined here can also be used with
+ # dynamic expansions, under a few conditions:
+ #
+ # * The section is "redundant", or "load-balance", or
+ # "redundant-load-balance"
+ # * The section contains modules ONLY, and no sub-sections
+ # * all modules in the section are using the same rlm_
+ # driver, e.g. They are all sql, or all ldap, etc.
+ #
+ # When those conditions are satisfied, the server will
+ # automatically register a dynamic expansion, using the
+ # name of the "virtual" module. In the example below,
+ # it will be "redundant_sql". You can then use this expansion
+ # just like any other:
+ #
+ # update reply {
+ # Filter-Id := "%{redundant_sql: ... }"
+ # }
+ #
+ # In this example, the expansion is done via module "sql1",
+ # and if that expansion fails, using module "sql2".
+ #
+ # For best results, configure the "pool" subsection of the
+ # module so that "retry_delay" is non-zero. That will allow
+ # the redundant block to quickly ignore all "down" SQL
+ # databases. If instead we have "retry_delay = 0", then
+ # every time the redundant block is used, the server will try
+ # to open a connection to every "down" database, causing
+ # problems.
+ #
#redundant redundant_sql {
# sql1
# sql2
######################################################################
#
-# SNMP notifications. Uncomment the following line to enable
-# snmptraps. Note that you MUST also configure the full path
-# to the "snmptrap" command in the "trigger.conf" file.
-#
-#$INCLUDE trigger.conf
-
-######################################################################
-#
# Load virtual servers.
#
# This next $INCLUDE line loads files in the directory that
projects / freeradius.git / blobdiff