P2P: Implement P2P_GO_FREQ_MOVE_SCM_ECSA policy

[mech_eap.git] / wpa_supplicant / config.h

diff --git a/wpa_supplicant/config.h b/wpa_supplicant/config.h
index 545a4bd..68d64fa 100644 (file)
--- a/wpa_supplicant/config.h
+++ b/wpa_supplicant/config.h
@@ -18,6 +18,11 @@
 #define DEFAULT_USER_MPM 1
 #define DEFAULT_MAX_PEER_LINKS 99
 #define DEFAULT_MESH_MAX_INACTIVITY 300
+/*
+ * The default dot11RSNASAERetransPeriod is defined as 40 ms in the standard,
+ * but use 1000 ms in practice to avoid issues on low power CPUs.
+ */
+#define DEFAULT_DOT11_RSNA_SAE_RETRANS_PERIOD 1000
 #define DEFAULT_FAST_REAUTH 1
 #define DEFAULT_P2P_GO_INTENT 7
 #define DEFAULT_P2P_INTRA_BSS 1
@@ -401,6 +406,11 @@ struct wpa_config {
         * one by one until the driver reports successful association; each
         * network block should have explicit security policy (i.e., only one
         * option in the lists) for key_mgmt, pairwise, group, proto variables.
+        *
+        * Note: ap_scan=2 should not be used with the nl80211 driver interface
+        * (the current Linux interface). ap_scan=1 is optimized work working
+        * with nl80211. For finding networks using hidden SSID, scan_ssid=1 in
+        * the network block can be used with nl80211.
         */
        int ap_scan;
 
@@ -734,6 +744,39 @@ struct wpa_config {
        int p2p_group_idle;
 
        /**
+        * p2p_go_freq_change_policy - The GO frequency change policy
+        *
+        * This controls the behavior of the GO when there is a change in the
+        * map of the currently used frequencies in case more than one channel
+        * is supported.
+        *
+        * @P2P_GO_FREQ_MOVE_SCM: Prefer working in a single channel mode if
+        * possible. In case the GO is the only interface using its frequency
+        * and there are other station interfaces on other frequencies, the GO
+        * will migrate to one of these frequencies.
+        *
+        * @P2P_GO_FREQ_MOVE_SCM_PEER_SUPPORTS: Same as P2P_GO_FREQ_MOVE_SCM,
+        * but a transition is possible only in case one of the other used
+        * frequencies is one of the frequencies in the intersection of the
+        * frequency list of the local device and the peer device.
+        *
+        * @P2P_GO_FREQ_MOVE_STAY: Prefer to stay on the current frequency.
+        *
+        * @P2P_GO_FREQ_MOVE_SCM_ECSA: Same as
+        * P2P_GO_FREQ_MOVE_SCM_PEER_SUPPORTS but a transition is possible only
+        * if all the group members advertise eCSA support.
+        */
+       enum {
+               P2P_GO_FREQ_MOVE_SCM = 0,
+               P2P_GO_FREQ_MOVE_SCM_PEER_SUPPORTS = 1,
+               P2P_GO_FREQ_MOVE_STAY = 2,
+               P2P_GO_FREQ_MOVE_SCM_ECSA = 3,
+               P2P_GO_FREQ_MOVE_MAX = P2P_GO_FREQ_MOVE_SCM_ECSA,
+       } p2p_go_freq_change_policy;
+
+#define DEFAULT_P2P_GO_FREQ_MOVE P2P_GO_FREQ_MOVE_STAY
+
+       /**
         * p2p_passphrase_len - Passphrase length (8..63) for P2P GO
         *
         * This parameter controls the length of the random passphrase that is
@@ -968,6 +1011,18 @@ struct wpa_config {
        int p2p_no_group_iface;
 
        /**
+        * p2p_cli_probe - Enable/disable P2P CLI probe request handling
+        *
+        * If this parameter is set to 1, a connected P2P Client will receive
+        * and handle Probe Request frames. Setting this parameter to 0
+        * disables this option. Default value: 0.
+        *
+        * Note: Setting this property at run time takes effect on the following
+        * interface state transition to/from the WPA_COMPLETED state.
+        */
+       int p2p_cli_probe;
+
+       /**
         * okc - Whether to enable opportunistic key caching by default
         *
         * By default, OKC is disabled unless enabled by the per-network
@@ -1149,6 +1204,15 @@ struct wpa_config {
        int mesh_max_inactivity;
 
        /**
+        * dot11RSNASAERetransPeriod - Timeout to retransmit SAE Auth frame
+        *
+        * This timeout value is used in mesh STA to retransmit
+        * SAE Authentication frame.
+        * By default: 1000 milliseconds.
+        */
+       int dot11RSNASAERetransPeriod;
+
+       /**
         * passive_scan - Whether to force passive scan for network connection
         *
         * This parameter can be used to force only passive scanning to be used
@@ -1172,6 +1236,22 @@ struct wpa_config {
         * by executing the WPS protocol.
         */
        int wps_priority;
+
+       /**
+        * fst_group_id - FST group ID
+        */
+       char *fst_group_id;
+
+       /**
+        * fst_priority - priority of the interface within the FST group
+        */
+       int fst_priority;
+
+       /**
+        * fst_llt - default FST LLT (Link-Lost Timeout) to be used for the
+        * interface.
+        */
+       int fst_llt;
 };