# This is an optional set of parameters for automatic scanning
# within an interface in following format:
#autoscan=<autoscan module name>:<module parameters>
-# autoscan is like bgscan but on disconnected or inactive state.
-# For instance, on exponential module parameters would be <base>:<limit>
+# autoscan is like bgscan but on disconnected or inactive state.
+# For instance, on exponential module parameters would be <base>:<limit>
#autoscan=exponential:3:300
# Which means a delay between scans on a base exponential of 3,
-# up to the limit of 300 seconds (3, 9, 27 ... 300)
-# For periodic module, parameters would be <fixed interval>
+# up to the limit of 300 seconds (3, 9, 27 ... 300)
+# For periodic module, parameters would be <fixed interval>
#autoscan=periodic:30
-# So a delay of 30 seconds will be applied between each scan
+# So a delay of 30 seconds will be applied between each scan
# filter_ssids - SSID-based scan result filtering
# 0 = do not filter scan results (default)
# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9
#sae_groups=21 20 19 26 25
+# Default value for DTIM period (if not overridden in network block)
+#dtim_period=2
+
+# Default value for Beacon interval (if not overridden in network block)
+#beacon_int=100
+
+# Additional vendor specific elements for Beacon and Probe Response frames
+# This parameter can be used to add additional vendor specific element(s) into
+# the end of the Beacon and Probe Response frames. The format for these
+# element(s) is a hexdump of the raw information elements (id+len+payload for
+# one or more elements). This is used in AP and P2P GO modes.
+#ap_vendor_elements=dd0411223301
+
+# Ignore scan results older than request
+#
+# The driver may have a cache of scan results that makes it return
+# information that is older than our scan trigger. This parameter can
+# be used to configure such old information to be ignored instead of
+# allowing it to update the internal BSS table.
+#ignore_old_scan_res=0
+
+# scan_cur_freq: Whether to scan only the current frequency
+# 0: Scan all available frequencies. (Default)
+# 1: Scan current operating frequency if another VIF on the same radio
+# is already associated.
+
# Interworking (IEEE 802.11u)
# Enable Interworking
# milenage: Milenage parameters for SIM/USIM simulator in <Ki>:<OPc>:<SQN>
# format
#
-# domain: Home service provider FQDN
+# domain: Home service provider FQDN(s)
# This is used to compare against the Domain Name List to figure out
-# whether the AP is operated by the Home SP.
+# whether the AP is operated by the Home SP. Multiple domain entries can
+# be used to configure alternative FQDNs that will be considered home
+# networks.
#
# roaming_consortium: Roaming Consortium OI
# If roaming_consortium_len is non-zero, this field contains the
# set, scan results that do not match any of the specified frequencies are not
# considered when selecting a BSS.
#
+# This can also be set on the outside of the network block. In this case,
+# it limits the frequencies that will be scanned.
+#
# bgscan: Background scanning
# wpa_supplicant behavior for background scanning can be specified by
# configuring a bgscan module. These modules are responsible for requesting
# interface used for EAPOL. The default value is suitable for most
# cases.
#
+# ocsp: Whether to use/require OCSP to check server certificate
+# 0 = do not use OCSP stapling (TLS certificate status extension)
+# 1 = try to use OCSP stapling, but not require response
+# 2 = require valid OCSP stapling response
+#
# EAP-FAST variables:
# pac_file: File path for the PAC entries. wpa_supplicant will need to be able
# to create this file and write updates to it when PAC is being
# DTIM period in Beacon intervals for AP mode (default: 2)
#dtim_period=2
+# Beacon interval (default: 100 TU)
+#beacon_int=100
+
# disable_ht: Whether HT (802.11n) should be disabled.
# 0 = HT enabled (if AP supports it)
# 1 = HT disabled
# -1 = Do not make any changes.
# 0-3 = Set AMPDU density (aka factor) to specified value.
+# disable_vht: Whether VHT should be disabled.
+# 0 = VHT enabled (if AP supports it)
+# 1 = VHT disabled
+#
+# vht_capa: VHT capabilities to set in the override
+# vht_capa_mask: mask of VHT capabilities
+#
+# vht_rx_mcs_nss_1/2/3/4/5/6/7/8: override the MCS set for RX NSS 1-8
+# vht_tx_mcs_nss_1/2/3/4/5/6/7/8: override the MCS set for TX NSS 1-8
+# 0: MCS 0-7
+# 1: MCS 0-8
+# 2: MCS 0-9
+# 3: not supported
+
# Example blocks:
# Simple case: WPA-PSK, PSK as an ASCII passphrase, allow all valid ciphers
network={
key_mgmt=NONE
}
+
+
+# Example config file that will only scan on channel 36.
+freq_list=5180
+network={
+ key_mgmt=NONE
+}