Sync with wireless-testing.git linux/nl80211.h

diff --git a/src/drivers/nl80211_copy.h b/src/drivers/nl80211_copy.h
index 3769303..8aa7bad 100644 (file)
--- a/src/drivers/nl80211_copy.h
+++ b/src/drivers/nl80211_copy.h
@@ -769,6 +769,8 @@ enum nl80211_commands {
  *     that can be added to a scan request
  * @NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN: maximum length of information
  *     elements that can be added to a scheduled scan request
+ * @NL80211_ATTR_MAX_MATCH_SETS: maximum number of sets that can be
+ *     used with @NL80211_ATTR_SCHED_SCAN_MATCH, a wiphy attribute.
  *
  * @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz)
  * @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive
@@ -1011,6 +1013,24 @@ enum nl80211_commands {
 
  * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan
  *     cycles, in msecs.
+
+ * @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more
+ *     sets of attributes to match during scheduled scans.  Only BSSs
+ *     that match any of the sets will be reported.  These are
+ *     pass-thru filter rules.
+ *     For a match to succeed, the BSS must match all attributes of a
+ *     set.  Since not every hardware supports matching all types of
+ *     attributes, there is no guarantee that the reported BSSs are
+ *     fully complying with the match sets and userspace needs to be
+ *     able to ignore them by itself.
+ *     Thus, the implementation is somewhat hardware-dependent, but
+ *     this is only an optimization and the userspace application
+ *     needs to handle all the non-filtered results anyway.
+ *     If the match attributes don't make sense when combined with
+ *     the values passed in @NL80211_ATTR_SCAN_SSIDS (eg. if an SSID
+ *     is included in the probe request, but the match attributes
+ *     will never let it go through), -EINVAL may be returned.
+ *     If ommited, no filtering is done.
  *
  * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported
  *     interface combinations. In each nested item, it contains attributes
@@ -1042,6 +1062,14 @@ enum nl80211_commands {
  *     (Re)Association Response frames when the driver (or firmware) replies to
  *     (Re)Association Request frames.
  *
+ * @NL80211_ATTR_STA_WME: Nested attribute containing the wme configuration
+ *     of the station, see &enum nl80211_sta_wme_attr.
+ * @NL80211_ATTR_SUPPORT_AP_UAPSD: the device supports uapsd when working
+ *     as AP.
+ *
+ * @NL80211_ATTR_ROAM_SUPPORT: Indicates whether the firmware is capable of
+ *     roaming to another AP in the same ESS if the signal lever is low.
+ *
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
  */
@@ -1252,6 +1280,14 @@ enum nl80211_attrs {
        NL80211_ATTR_IE_PROBE_RESP,
        NL80211_ATTR_IE_ASSOC_RESP,
 
+       NL80211_ATTR_STA_WME,
+       NL80211_ATTR_SUPPORT_AP_UAPSD,
+
+       NL80211_ATTR_ROAM_SUPPORT,
+
+       NL80211_ATTR_SCHED_SCAN_MATCH,
+       NL80211_ATTR_MAX_MATCH_SETS,
+
        /* add attributes here, update the policy in nl80211.c */
 
        __NL80211_ATTR_AFTER_LAST,
@@ -1711,6 +1747,26 @@ enum nl80211_reg_rule_attr {
 };
 
 /**
+ * enum nl80211_sched_scan_match_attr - scheduled scan match attributes
+ * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved
+ * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching,
+ * only report BSS with matching SSID.
+ * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter
+ *     attribute number currently defined
+ * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use
+ */
+enum nl80211_sched_scan_match_attr {
+       __NL80211_SCHED_SCAN_MATCH_ATTR_INVALID,
+
+       NL80211_ATTR_SCHED_SCAN_MATCH_SSID,
+
+       /* keep last */
+       __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST,
+       NL80211_SCHED_SCAN_MATCH_ATTR_MAX =
+               __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1
+};
+
+/**
  * enum nl80211_reg_rule_flags - regulatory rule flags
  *
  * @NL80211_RRF_NO_OFDM: OFDM modulation not allowed
@@ -2482,4 +2538,22 @@ enum nl80211_hidden_ssid {
        NL80211_HIDDEN_SSID_ZERO_CONTENTS
 };
 
+/**
+ * enum nl80211_sta_wme_attr - station WME attributes
+ * @__NL80211_STA_WME_INVALID: invalid number for nested attribute
+ * @NL80211_STA_WME_QUEUES: bitmap of uapsd queues.
+ * @NL80211_STA_WME_MAX_SP: max service period.
+ * @__NL80211_STA_WME_AFTER_LAST: internal
+ * @NL80211_STA_WME_MAX: highest station WME attribute
+ */
+enum nl80211_sta_wme_attr {
+       __NL80211_STA_WME_INVALID,
+       NL80211_STA_WME_UAPSD_QUEUES,
+       NL80211_STA_WME_MAX_SP,
+
+       /* keep last */
+       __NL80211_STA_WME_AFTER_LAST,
+       NL80211_STA_WME_MAX = __NL80211_STA_WME_AFTER_LAST - 1
+};
+
 #endif /* __LINUX_NL80211_H */