# management frames); ath0 for madwifi
interface=wlan0
-# In case of madwifi driver, an additional configuration parameter, bridge,
-# must be used to notify hostapd if the interface is included in a bridge. This
-# parameter is not used with Host AP driver.
+# In case of madwifi, atheros, and nl80211 driver interfaces, an additional
+# configuration parameter, bridge, may be used to notify hostapd if the
+# interface is included in a bridge. This parameter is not used with Host AP
+# driver. If the bridge parameter is not set, the drivers will automatically
+# figure out the bridge interface (assuming sysfs is enabled and mounted to
+# /sys) and this parameter may not be needed.
+#
+# For nl80211, this parameter can be used to request the AP interface to be
+# added to the bridge automatically (brctl may refuse to do this before hostapd
+# has been started to change the interface mode). If needed, the bridge
+# interface is also created.
#bridge=br0
-# Driver interface type (hostap/wired/madwifi/prism54/test/nl80211/bsd);
-# default: hostap)
-# Use driver=test if building hostapd as a standalone RADIUS server that does
+# Driver interface type (hostap/wired/madwifi/test/none/nl80211/bsd);
+# default: hostap). nl80211 is used with all Linux mac80211 drivers.
+# Use driver=none if building hostapd as a standalone RADIUS server that does
# not control any wireless/wired driver.
# driver=hostap
# SSID to be used in IEEE 802.11 management frames
ssid=test
-# Country code (ISO/IEC 3166-1). Used to set regulatory domain.
-# Modify as needed to indicate country in which device is operating.
+# Country code (ISO/IEC 3166-1). Used to set regulatory domain.
+# Set as needed to indicate country in which device is operating.
# This can limit available channels and transmit power.
-# (default: US)
#country_code=US
# Enable IEEE 802.11d. This advertises the country_code and the set of allowed
# (default: 0 = disabled)
#ieee80211d=1
-# Enable IEEE 802.11h. This enables the TPC and DFS services when operating
-# in a regulatory domain which requires them. Once enabled it will be
-# operational only when working in hw_mode a and in countries where it is
-# required. The end user should not be allowed to disable this.
-# The country_code setting must be configured with the correct country for
-# IEEE 802.11h to function.
-# When IEEE 802.11h is operational, the channel_policy and configured channel
-# settings will be ignored but will behave as though the channel_policy is
-# set to "3" (automatic channel selection). When IEEE 802.11h is enabled but
-# not operational (for example, if the radio mode is changed from "a" to "b")
-# the channel_policy and channel settings take effect again.
-# (default: 1 = enabled)
-#ieee80211h=1
-
# Operation mode (a = IEEE 802.11a, b = IEEE 802.11b, g = IEEE 802.11g,
# Default: IEEE 802.11b
hw_mode=a
# Channel number (IEEE 802.11)
-# (default: 0, i.e., not set, used with channel_policy=2)
+# (default: 0, i.e., not set)
+# Please note that some drivers (e.g., madwifi) do not use this value from
+# hostapd and the channel will need to be configuration separately with
+# iwconfig.
channel=60
# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535)
#basic_rates=10 20 55 110
#basic_rates=60 120 240
+# Short Preamble
+# This parameter can be used to enable optional use of short preamble for
+# frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network performance.
+# This applies only to IEEE 802.11b-compatible networks and this should only be
+# enabled if the local hardware supports use of short preamble. If any of the
+# associated STAs do not support short preamble, use of short preamble will be
+# disabled (and enabled when such STAs disassociate) dynamically.
+# 0 = do not allow use of short preamble (default)
+# 1 = allow use of short preamble
+#preamble=1
+
# Station MAC address -based authentication
# Please note that this kind of access control requires a driver that uses
# hostapd to take care of management frame processing and as such, this can be
#tx_queue_beacon_cwmax=7
#tx_queue_beacon_burst=1.5
-# 802.1D Tag to AC mappings
+# 802.1D Tag (= UP) to AC mappings
# WMM specifies following mapping of data frames to different ACs. This mapping
# can be configured using Linux QoS/tc and sch_pktpri.o module.
# 802.1D Tag 802.1D Designation Access Category WMM Designation
# 1 BK AC_BK Background
# 2 - AC_BK Background
# 0 BE AC_BE Best Effort
-# 3 EE AC_VI Video
+# 3 EE AC_BE Best Effort
# 4 CL AC_VI Video
# 5 VI AC_VI Video
# 6 VO AC_VO Voice
# note - here cwMin and cmMax are in exponent form. the actual cw value used
# will be (2^n)-1 where n is the value given here
#
-wme_enabled=1
+wmm_enabled=1
+#
+# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD]
+# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver)
+#uapsd_advertisement_enabled=1
#
# Low priority / AC_BK = background
-wme_ac_bk_cwmin=4
-wme_ac_bk_cwmax=10
-wme_ac_bk_aifs=7
-wme_ac_bk_txop_limit=0
-wme_ac_bk_acm=0
+wmm_ac_bk_cwmin=4
+wmm_ac_bk_cwmax=10
+wmm_ac_bk_aifs=7
+wmm_ac_bk_txop_limit=0
+wmm_ac_bk_acm=0
# Note: for IEEE 802.11b mode: cWmin=5 cWmax=10
#
# Normal priority / AC_BE = best effort
-wme_ac_be_aifs=3
-wme_ac_be_cwmin=4
-wme_ac_be_cwmax=10
-wme_ac_be_txop_limit=0
-wme_ac_be_acm=0
+wmm_ac_be_aifs=3
+wmm_ac_be_cwmin=4
+wmm_ac_be_cwmax=10
+wmm_ac_be_txop_limit=0
+wmm_ac_be_acm=0
# Note: for IEEE 802.11b mode: cWmin=5 cWmax=7
#
# High priority / AC_VI = video
-wme_ac_vi_aifs=2
-wme_ac_vi_cwmin=3
-wme_ac_vi_cwmax=4
-wme_ac_vi_txop_limit=94
-wme_ac_vi_acm=0
+wmm_ac_vi_aifs=2
+wmm_ac_vi_cwmin=3
+wmm_ac_vi_cwmax=4
+wmm_ac_vi_txop_limit=94
+wmm_ac_vi_acm=0
# Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188
#
# Highest priority / AC_VO = voice
-wme_ac_vo_aifs=2
-wme_ac_vo_cwmin=2
-wme_ac_vo_cwmax=3
-wme_ac_vo_txop_limit=47
-wme_ac_vo_acm=0
+wmm_ac_vo_aifs=2
+wmm_ac_vo_cwmin=2
+wmm_ac_vo_cwmax=3
+wmm_ac_vo_txop_limit=47
+wmm_ac_vo_acm=0
# Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102
-# Associate as a station to another AP while still acting as an AP on the same
-# channel.
-#assoc_ap_addr=00:12:34:56:78:9a
-
# Static WEP key configuration
#
# The key number to use when transmitting.
# default: 300 (i.e., 5 minutes)
#ap_max_inactivity=300
-# Enable/disable internal bridge for packets between associated stations.
-#
-# When IEEE 802.11 is used in managed mode, packets are usually send through
-# the AP even if they are from a wireless station to another wireless station.
-# This functionality requires that the AP has a bridge functionality that sends
-# frames back to the same interface if their destination is another associated
-# station. In addition, broadcast/multicast frames from wireless stations will
-# be sent both to the host system net stack (e.g., to eventually wired network)
-# and back to the wireless interface.
-#
-# The internal bridge is implemented within the wireless kernel module and it
-# bypasses kernel filtering (netfilter/iptables/ebtables). If direct
-# communication between the stations needs to be prevented, the internal
-# bridge can be disabled by setting bridge_packets=0.
-#
-# Note: If this variable is not included in hostapd.conf, hostapd does not
-# change the configuration and iwpriv can be used to set the value with
-# 'iwpriv wlan# param 10 0' command. If the variable is in hostapd.conf,
-# hostapd will override possible iwpriv configuration whenever configuration
-# file is reloaded.
-#
-# default: do not control from hostapd (80211.o defaults to 1=enabled)
-#bridge_packets=1
-
# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to
# remain asleep). Default: 65535 (no limit apart from field size)
#max_listen_interval=100
+# WDS (4-address frame) mode with per-station virtual interfaces
+# (only supported with driver=nl80211)
+# This mode allows associated stations to use 4-address frames to allow layer 2
+# bridging to be used.
+#wds_sta=1
+
+##### IEEE 802.11n related configuration ######################################
+
+# ieee80211n: Whether IEEE 802.11n (HT) is enabled
+# 0 = disabled (default)
+# 1 = enabled
+# Note: You will also need to enable WMM for full HT functionality.
+#ieee80211n=1
+
+# ht_capab: HT capabilities (list of flags)
+# LDPC coding capability: [LDPC] = supported
+# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary
+# channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz
+# with secondary channel below the primary channel
+# (20 MHz only if neither is set)
+# Note: There are limits on which channels can be used with HT40- and
+# HT40+. Following table shows the channels that may be available for
+# HT40- and HT40+ use per IEEE 802.11n Annex J:
+# freq HT40- HT40+
+# 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan)
+# 5 GHz 40,48,56,64 36,44,52,60
+# (depending on the location, not all of these channels may be available
+# for use)
+# Please note that 40 MHz channels may switch their primary and secondary
+# channels if needed or creation of 40 MHz channel maybe rejected based
+# on overlapping BSSes. These changes are done automatically when hostapd
+# is setting up the 40 MHz channel.
+# Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC]
+# (SMPS disabled if neither is set)
+# HT-greenfield: [GF] (disabled if not set)
+# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set)
+# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set)
+# Tx STBC: [TX-STBC] (disabled if not set)
+# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial
+# streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC
+# disabled if none of these set
+# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set)
+# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not
+# set)
+# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set)
+# PSMP support: [PSMP] (disabled if not set)
+# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set)
+#ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40]
+
##### IEEE 802.1X-2004 related configuration ##################################
# Require IEEE 802.1X authorization
# ephemeral DH keys. This can be used to achieve forward secrecy. If the file
# is in DSA parameters format, it will be automatically converted into DH
# params. This parameter is required if anonymous EAP-FAST is used.
+# You can generate DH parameters file with OpenSSL, e.g.,
+# "openssl dhparam -out /etc/hostapd.dh.pem 1024"
#dh_file=/etc/hostapd.dh.pem
+# Fragment size for EAP methods
+#fragment_size=1400
+
# Configuration data for EAP-SIM database/authentication gateway interface.
# This is a text string in implementation specific format. The example
# implementation in eap_sim_db.c uses this as the UNIX domain socket name for
#pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f
# EAP-FAST authority identity (A-ID)
-#eap_fast_a_id=test server
+# A-ID indicates the identity of the authority that issues PACs. The A-ID
+# should be unique across all issuing servers. In theory, this is a variable
+# length field, but due to some existing implementations requiring A-ID to be
+# 16 octets in length, it is strongly recommended to use that length for the
+# field to provid interoperability with deployed peer implementations. This
+# field is configured in hex format.
+#eap_fast_a_id=101112131415161718191a1b1c1d1e1f
+
+# EAP-FAST authority identifier information (A-ID-Info)
+# This is a user-friendly name for the A-ID. For example, the enterprise name
+# and server name in a human-readable format. This field is encoded as UTF-8.
+#eap_fast_a_id_info=test server
+
+# Enable/disable different EAP-FAST provisioning modes:
+#0 = provisioning disabled
+#1 = only anonymous provisioning allowed
+#2 = only authenticated provisioning allowed
+#3 = both provisioning modes allowed (default)
+#eap_fast_prov=3
+
+# EAP-FAST PAC-Key lifetime in seconds (hard limit)
+#pac_key_lifetime=604800
+
+# EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard
+# limit). The server will generate a new PAC-Key when this number of seconds
+# (or fewer) of the lifetime remains.
+#pac_key_refresh_time=86400
# EAP-SIM and EAP-AKA protected success/failure indication using AT_RESULT_IND
# (default: 0 = disabled).
#eap_sim_aka_result_ind=1
+# Trusted Network Connect (TNC)
+# If enabled, TNC validation will be required before the peer is allowed to
+# connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other
+# EAP method is enabled, the peer will be allowed to connect without TNC.
+#tnc=1
+
##### IEEE 802.11f - Inter-Access Point Protocol (IAPP) #######################
# attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN),
# Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value
# VLANID as a string). vlan_file option below must be configured if dynamic
-# VLANs are used.
+# VLANs are used. Optionally, the local MAC ACL list (accept_mac_file) can be
+# used to set static client MAC address to VLAN ID mapping.
# 0 = disabled (default)
# 1 = option; use default interface if RADIUS server does not include VLAN ID
# 2 = required; reject authentication if RADIUS server does not include VLAN ID
#wpa_psk_file=/etc/hostapd.wpa_psk
# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The
-# entries are separated with a space.
+# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be
+# added to enable SHA256-based stronger algorithms.
# (dot11RSNAConfigAuthenticationSuitesTable)
#wpa_key_mgmt=WPA-PSK WPA-EAP
# (in seconds).
#wpa_gmk_rekey=86400
+# Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of
+# PTK to mitigate some attacks against TKIP deficiencies.
+#wpa_ptk_rekey=600
+
# Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up
# roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN
# authentication and key handshake before actually associating with a new AP.
# 1 = enabled
#peerkey=1
-# ieee80211w: Whether management frame protection is enabled
+# ieee80211w: Whether management frame protection (MFP) is enabled
# 0 = disabled (default)
# 1 = optional
# 2 = required
#ieee80211w=0
+# Association SA Query maximum timeout (in TU = 1.024 ms; for MFP)
+# (maximum time to wait for a SA Query response)
+# dot11AssociationSAQueryMaximumTimeout, 1...4294967295
+#assoc_sa_query_max_timeout=1000
+
+# Association SA Query retry timeout (in TU = 1.024 ms; for MFP)
+# (time between two subsequent SA Query requests)
+# dot11AssociationSAQueryRetryTimeout, 1...4294967295
+#assoc_sa_query_retry_timeout=201
+
+
+# okc: Opportunistic Key Caching (aka Proactive Key Caching)
+# Allow PMK cache to be shared opportunistically among configured interfaces
+# and BSSes (i.e., all configurations within a single hostapd process).
+# 0 = disabled (default)
+# 1 = enabled
+#okc=1
+
##### IEEE 802.11r configuration ##############################################
# And so on.. One line per R0KH.
# List of R1KHs in the same Mobility Domain
-# format: <MAC address> <R0KH-ID> <128-bit key as hex string>
+# format: <MAC address> <R1KH-ID> <128-bit key as hex string>
# This list is used to map R1KH-ID to a destination MAC address when sending
# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD
# that can request PMK-R1 keys.
# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived
#pmk_r1_push=1
-##### Passive scanning ########################################################
-# Scan different channels every N seconds. 0 = disable passive scanning.
-#passive_scan_interval=60
-
-# Listen N usecs on each channel when doing passive scanning.
-# This value plus the time needed for changing channels should be less than
-# 32 milliseconds (i.e. 32000 usec) to avoid interruptions to normal
-# operations. Time needed for channel changing varies based on the used wlan
-# hardware.
-# default: disabled (0)
-#passive_scan_listen=10000
-
-# Passive scanning mode:
-# 0 = scan all supported modes (802.11a/b/g/Turbo) (default)
-# 1 = scan only the mode that is currently used for normal operations
-#passive_scan_mode=1
-
-# Maximum number of entries kept in AP table (either for passive scanning or
-# for detecting Overlapping Legacy BSS Condition). The oldest entry will be
+##### Neighbor table ##########################################################
+# Maximum number of entries kept in AP table (either for neigbor table or for
+# detecting Overlapping Legacy BSS Condition). The oldest entry will be
# removed when adding a new entry that would make the list grow over this
-# limit. Note! Wi-Fi certification for IEEE 802.11g requires that OLBC is
+# limit. Note! WFA certification for IEEE 802.11g requires that OLBC is
# enabled, so this field should not be set to 0 when using IEEE 802.11g.
# default: 255
#ap_table_max_size=255
#ap_table_expiration_time=3600
+##### Wi-Fi Protected Setup (WPS) #############################################
+
+# WPS state
+# 0 = WPS disabled (default)
+# 1 = WPS enabled, not configured
+# 2 = WPS enabled, configured
+#wps_state=2
+
+# AP can be configured into a locked state where new WPS Registrar are not
+# accepted, but previously authorized Registrars (including the internal one)
+# can continue to add new Enrollees.
+#ap_setup_locked=1
+
+# Universally Unique IDentifier (UUID; see RFC 4122) of the device
+# This value is used as the UUID for the internal WPS Registrar. If the AP
+# is also using UPnP, this value should be set to the device's UPnP UUID.
+# If not configured, UUID will be generated based on the local MAC address.
+#uuid=12345678-9abc-def0-1234-56789abcdef0
+
+# Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs
+# that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the
+# default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of
+# per-device PSKs is recommended as the more secure option (i.e., make sure to
+# set wpa_psk_file when using WPS with WPA-PSK).
+
+# When an Enrollee requests access to the network with PIN method, the Enrollee
+# PIN will need to be entered for the Registrar. PIN request notifications are
+# sent to hostapd ctrl_iface monitor. In addition, they can be written to a
+# text file that could be used, e.g., to populate the AP administration UI with
+# pending PIN requests. If the following variable is set, the PIN requests will
+# be written to the configured file.
+#wps_pin_requests=/var/run/hostapd_wps_pin_requests
+
+# Device Name
+# User-friendly description of device; up to 32 octets encoded in UTF-8
+#device_name=Wireless AP
+
+# Manufacturer
+# The manufacturer of the device (up to 64 ASCII characters)
+#manufacturer=Company
+
+# Model Name
+# Model of the device (up to 32 ASCII characters)
+#model_name=WAP
+
+# Model Number
+# Additional device description (up to 32 ASCII characters)
+#model_number=123
+
+# Serial Number
+# Serial number of the device (up to 32 characters)
+#serial_number=12345
+
+# Primary Device Type
+# Used format: <categ>-<OUI>-<subcateg>
+# categ = Category as an integer value
+# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for
+# default WPS OUI
+# subcateg = OUI-specific Sub Category as an integer value
+# Examples:
+# 1-0050F204-1 (Computer / PC)
+# 1-0050F204-2 (Computer / Server)
+# 5-0050F204-1 (Storage / NAS)
+# 6-0050F204-1 (Network Infrastructure / AP)
+#device_type=6-0050F204-1
+
+# OS Version
+# 4-octet operating system version number (hex string)
+#os_version=01020300
+
+# Config Methods
+# List of the supported configuration methods
+# Available methods: usba ethernet label display ext_nfc_token int_nfc_token
+# nfc_interface push_button keypad virtual_display physical_display
+# virtual_push_button physical_push_button
+#config_methods=label virtual_display virtual_push_button keypad
+
+# Static access point PIN for initial configuration and adding Registrars
+# If not set, hostapd will not allow external WPS Registrars to control the
+# access point. The AP PIN can also be set at runtime with hostapd_cli
+# wps_ap_pin command. Use of temporary (enabled by user action) and random
+# AP PIN is much more secure than configuring a static AP PIN here. As such,
+# use of the ap_pin parameter is not recommended if the AP device has means for
+# displaying a random PIN.
+#ap_pin=12345670
+
+# Skip building of automatic WPS credential
+# This can be used to allow the automatically generated Credential attribute to
+# be replaced with pre-configured Credential(s).
+#skip_cred_build=1
+
+# Additional Credential attribute(s)
+# This option can be used to add pre-configured Credential attributes into M8
+# message when acting as a Registrar. If skip_cred_build=1, this data will also
+# be able to override the Credential attribute that would have otherwise been
+# automatically generated based on network configuration. This configuration
+# option points to an external file that much contain the WPS Credential
+# attribute(s) as binary data.
+#extra_cred=hostapd.cred
+
+# Credential processing
+# 0 = process received credentials internally (default)
+# 1 = do not process received credentials; just pass them over ctrl_iface to
+# external program(s)
+# 2 = process received credentials internally and pass them over ctrl_iface
+# to external program(s)
+# Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and
+# extra_cred be used to provide the Credential data for Enrollees.
+#
+# wps_cred_processing=1 will disabled automatic updates of hostapd.conf file
+# both for Credential processing and for marking AP Setup Locked based on
+# validation failures of AP PIN. An external program is responsible on updating
+# the configuration appropriately in this case.
+#wps_cred_processing=0
+
+# AP Settings Attributes for M7
+# By default, hostapd generates the AP Settings Attributes for M7 based on the
+# current configuration. It is possible to override this by providing a file
+# with pre-configured attributes. This is similar to extra_cred file format,
+# but the AP Settings attributes are not encapsulated in a Credential
+# attribute.
+#ap_settings=hostapd.ap_settings
+
+# WPS UPnP interface
+# If set, support for external Registrars is enabled.
+#upnp_iface=br0
+
+# Friendly Name (required for UPnP)
+# Short description for end use. Should be less than 64 characters.
+#friendly_name=WPS Access Point
+
+# Manufacturer URL (optional for UPnP)
+#manufacturer_url=http://www.example.com/
+
+# Model Description (recommended for UPnP)
+# Long description for end user. Should be less than 128 characters.
+#model_description=Wireless Access Point
+
+# Model URL (optional for UPnP)
+#model_url=http://www.example.com/model/
+
+# Universal Product Code (optional for UPnP)
+# 12-digit, all-numeric code that identifies the consumer package.
+#upc=123456789012
+
+##### Wi-Fi Direct (P2P) ######################################################
+
+# Enable P2P Device management
+#manage_p2p=1
+
+# Allow cross connection
+#allow_cross_connection=1
+
##### Multiple BSSID support ##################################################
#
# Above configuration is using the default interface (wlan#, or multi-SSID VLAN
# hostapd will generate BSSID mask based on the BSSIDs that are
# configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is
# not the case, the MAC address of the radio must be changed before starting
-# hostapd (ifconfig wlan0 hw ether <MAC addr>).
+# hostapd (ifconfig wlan0 hw ether <MAC addr>). If a BSSID is configured for
+# every secondary BSS, this limitation is not applied at hostapd and other
+# masks may be used if the driver supports them (e.g., swap the locally
+# administered bit)
#
# BSSIDs are assigned in order to each BSS, unless an explicit BSSID is
# specified using the 'bssid' parameter.
projects / libeap.git / blobdiff