hostapd: Use stations nsts capability in (Re)Association Response frame

[mech_eap.git] / hostapd / hostapd.conf

diff --git a/hostapd/hostapd.conf b/hostapd/hostapd.conf
index dd7b466..4fc3278 100644 (file)
--- a/hostapd/hostapd.conf
+++ b/hostapd/hostapd.conf
@@ -3,6 +3,8 @@
 
 # AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for
 # management frames with the Host AP driver); wlan0 with many nl80211 drivers
+# Note: This attribute can be overridden by the values supplied with the '-i'
+# command line parameter.
 interface=wlan0
 
 # In case of atheros and nl80211 driver interfaces, an additional
@@ -283,6 +285,13 @@ ignore_broadcast_ssid=0
 # one or more elements)
 #vendor_elements=dd0411223301
 
+# Additional vendor specific elements for (Re)Association Response frames
+# This parameter can be used to add additional vendor specific element(s) into
+# the end of the (Re)Association Response frames. The format for these
+# element(s) is a hexdump of the raw information elements (id+len+payload for
+# one or more elements)
+#assocresp_elements=dd0411223301
+
 # TX queue parameters (EDCF / bursting)
 # tx_queue_<queue name>_<param>
 # queues: data0, data1, data2, data3, after_beacon, beacon
@@ -676,6 +685,13 @@ wmm_ac_vo_acm=0
 #
 #vht_oper_centr_freq_seg1_idx=159
 
+# Workaround to use station's nsts capability in (Re)Association Response frame
+# This may be needed with some deployed devices as an interoperability
+# workaround for beamforming if the AP's capability is greater than the
+# station's capability. This is disabled by default and can be enabled by
+# setting use_sta_nsts=1.
+#use_sta_nsts=0
+
 ##### IEEE 802.1X-2004 related configuration ##################################
 
 # Require IEEE 802.1X authorization
@@ -1079,6 +1095,9 @@ own_ip_addr=127.0.0.1
 #
 # DAS require Event-Timestamp
 #radius_das_require_event_timestamp=1
+#
+# DAS require Message-Authenticator
+#radius_das_require_message_authenticator=1
 
 ##### RADIUS authentication server configuration ##############################
 
@@ -1740,6 +1759,13 @@ own_ip_addr=127.0.0.1
 # For example, AP Civic Location ANQP-element with unknown location:
 #anqp_elem=266:000000
 
+# GAS Address 3 behavior
+# 0 = P2P specification (Address3 = AP BSSID) workaround enabled by default
+#     based on GAS request Address3
+# 1 = IEEE 802.11 standard compliant regardless of GAS request Address3
+# 2 = Force non-compliant behavior (Address3 = AP BSSID for all cases)
+#gas_address3=0
+
 # QoS Map Set configuration
 #
 # Comma delimited QoS Map Set in decimal values
@@ -1887,6 +1913,9 @@ own_ip_addr=127.0.0.1
 # The content of a location civic measurement subelement
 #civic=<Hexdump of binary data of the location civic report>
 
+# Enable neighbor report via radio measurements
+#rrm_neighbor_report=1
+
 ##### TESTING OPTIONS #########################################################
 #
 # The options in this section are only available when the build configuration