#define HOSTAPD_CHAN_INDOOR_ONLY 0x00010000
#define HOSTAPD_CHAN_GO_CONCURRENT 0x00020000
+#define HOSTAPD_CHAN_VHT_10_150 0x00100000
+#define HOSTAPD_CHAN_VHT_30_130 0x00200000
+#define HOSTAPD_CHAN_VHT_50_110 0x00400000
+#define HOSTAPD_CHAN_VHT_70_90 0x00800000
+#define HOSTAPD_CHAN_VHT_90_70 0x01000000
+#define HOSTAPD_CHAN_VHT_110_50 0x02000000
+#define HOSTAPD_CHAN_VHT_130_30 0x04000000
+#define HOSTAPD_CHAN_VHT_150_10 0x08000000
+
+/* Filter gratuitous ARP */
+#define WPA_DATA_FRAME_FILTER_FLAG_ARP BIT(0)
+/* Filter unsolicited Neighbor Advertisement */
+#define WPA_DATA_FRAME_FILTER_FLAG_NA BIT(1)
+/* Filter unicast IP packets encrypted using the GTK */
+#define WPA_DATA_FRAME_FILTER_FLAG_GTK BIT(2)
+
/**
* enum reg_change_initiator - Regulatory change initiator
*/
#define WPAS_MAX_SCAN_SSIDS 16
/**
+ * struct wpa_driver_scan_ssid - SSIDs to scan for
+ * @ssid - specific SSID to scan for (ProbeReq)
+ * %NULL or zero-length SSID is used to indicate active scan
+ * with wildcard SSID.
+ * @ssid_len - Length of the SSID in octets
+ */
+struct wpa_driver_scan_ssid {
+ const u8 *ssid;
+ size_t ssid_len;
+};
+
+/**
* struct wpa_driver_scan_params - Scan parameters
* Data for struct wpa_driver_ops::scan2().
*/
/**
* ssids - SSIDs to scan for
*/
- struct wpa_driver_scan_ssid {
- /**
- * ssid - specific SSID to scan for (ProbeReq)
- * %NULL or zero-length SSID is used to indicate active scan
- * with wildcard SSID.
- */
- const u8 *ssid;
- /**
- * ssid_len: Length of the SSID in octets
- */
- size_t ssid_len;
- } ssids[WPAS_MAX_SCAN_SSIDS];
+ struct wpa_driver_scan_ssid ssids[WPAS_MAX_SCAN_SSIDS];
/**
* num_ssids - Number of entries in ssids array
*/
const u8 *mac_addr_mask;
+ /**
+ * sched_scan_plans - Scan plans for scheduled scan
+ *
+ * Each scan plan consists of the number of iterations to scan and the
+ * interval between scans. When a scan plan finishes (i.e., it was run
+ * for the specified number of iterations), the next scan plan is
+ * executed. The scan plans are executed in the order they appear in
+ * the array (lower index first). The last scan plan will run infinitely
+ * (until requested to stop), thus must not specify the number of
+ * iterations. All other scan plans must specify the number of
+ * iterations.
+ */
+ struct sched_scan_plan {
+ u32 interval; /* In seconds */
+ u32 iterations; /* Zero to run infinitely */
+ } *sched_scan_plans;
+
+ /**
+ * sched_scan_plans_num - Number of scan plans in sched_scan_plans array
+ */
+ unsigned int sched_scan_plans_num;
+
+ /**
+ * bssid - Specific BSSID to scan for
+ *
+ * This optional parameter can be used to replace the default wildcard
+ * BSSID with a specific BSSID to scan for if results are needed from
+ * only a single BSS.
+ */
+ const u8 *bssid;
+
/*
* NOTE: Whenever adding new parameters here, please make sure
* wpa_scan_clone_params() and wpa_scan_free_params() get updated with
* RRM (Radio Resource Measurements)
*/
int rrm_used;
+
+ /**
+ * pbss - If set, connect to a PCP in a PBSS. Otherwise, connect to an
+ * AP as usual. Valid for DMG network only.
+ */
+ int pbss;
};
enum hide_ssid {
* reenable - Whether this is to re-enable beaconing
*/
int reenable;
+
+ /**
+ * pbss - Whether to start a PCP (in PBSS) instead of an AP in
+ * infrastructure BSS. Valid only for DMG network.
+ */
+ int pbss;
};
struct wpa_driver_mesh_bss_params {
-#define WPA_DRIVER_MESH_CONF_FLAG_AUTO_PLINKS 0x00000001
+#define WPA_DRIVER_MESH_CONF_FLAG_AUTO_PLINKS 0x00000001
+#define WPA_DRIVER_MESH_CONF_FLAG_PEER_LINK_TIMEOUT 0x00000002
+#define WPA_DRIVER_MESH_CONF_FLAG_MAX_PEER_LINKS 0x00000004
+#define WPA_DRIVER_MESH_CONF_FLAG_HT_OP_MODE 0x00000008
/*
* TODO: Other mesh configuration parameters would go here.
* See NL80211_MESHCONF_* for all the mesh config parameters.
*/
unsigned int flags;
+ int auto_plinks;
int peer_link_timeout;
+ int max_peer_links;
+ u16 ht_opmode;
};
struct wpa_driver_mesh_join_params {
int ie_len;
struct hostapd_freq_params freq;
int beacon_int;
- int max_peer_links;
+ int dtim_period;
struct wpa_driver_mesh_bss_params conf;
#define WPA_DRIVER_MESH_FLAG_USER_MPM 0x00000001
#define WPA_DRIVER_MESH_FLAG_DRIVER_MPM 0x00000002
#define WPA_DRIVER_FLAGS_VHT_IBSS 0x0000002000000000ULL
/** Driver supports automatic band selection */
#define WPA_DRIVER_FLAGS_SUPPORT_HW_MODE_ANY 0x0000004000000000ULL
+/** Driver supports simultaneous off-channel operations */
+#define WPA_DRIVER_FLAGS_OFFCHANNEL_SIMULTANEOUS 0x0000008000000000ULL
+/** Driver supports full AP client state */
+#define WPA_DRIVER_FLAGS_FULL_AP_CLIENT_STATE 0x0000010000000000ULL
+/** Driver supports P2P Listen offload */
+#define WPA_DRIVER_FLAGS_P2P_LISTEN_OFFLOAD 0x0000020000000000ULL
u64 flags;
+#define FULL_AP_CLIENT_STATE_SUPP(drv_flags) \
+ (drv_flags & WPA_DRIVER_FLAGS_FULL_AP_CLIENT_STATE)
+
#define WPA_DRIVER_SMPS_MODE_STATIC 0x00000001
#define WPA_DRIVER_SMPS_MODE_DYNAMIC 0x00000002
unsigned int smps_modes;
/** Maximum number of supported active probe SSIDs for sched_scan */
int max_sched_scan_ssids;
+ /** Maximum number of supported scan plans for scheduled scan */
+ unsigned int max_sched_scan_plans;
+
+ /** Maximum interval in a scan plan. In seconds */
+ u32 max_sched_scan_plan_interval;
+
+ /** Maximum number of iterations in a single scan plan */
+ u32 max_sched_scan_plan_iterations;
+
/** Whether sched_scan (offloaded scanning) is supported */
int sched_scan_supported;
* offset, namely the 6th byte in the Action frame body.
*/
#define WPA_DRIVER_FLAGS_TX_POWER_INSERTION 0x00000008
+/**
+ * Driver supports RRM. With this support, the driver will accept to use RRM in
+ * (Re)Association Request frames, without supporting quiet period.
+ */
+#define WPA_DRIVER_FLAGS_SUPPORT_RRM 0x00000010
+
u32 rrm_flags;
/* Driver concurrency capabilities */
unsigned int max_conc_chan_2_4;
/* Maximum number of concurrent channels on 5 GHz */
unsigned int max_conc_chan_5_0;
+
+ /* Maximum number of supported CSA counters */
+ u16 max_csa_counters;
};
struct hostapd_data;
struct hostap_sta_driver_data {
- unsigned long rx_packets, tx_packets, rx_bytes, tx_bytes;
+ unsigned long rx_packets, tx_packets;
+ unsigned long long rx_bytes, tx_bytes;
+ int bytes_64bit; /* whether 64-bit byte counters are supported */
unsigned long current_tx_rate;
unsigned long inactive_msec;
unsigned long flags;
u32 flags_mask; /* unset bits in flags */
#ifdef CONFIG_MESH
enum mesh_plink_state plink_state;
+ u16 peer_aid;
#endif /* CONFIG_MESH */
int set; /* Set STA parameters instead of add */
u8 qosinfo;
size_t supp_channels_len;
const u8 *supp_oper_classes;
size_t supp_oper_classes_len;
+ int support_p2p_ps;
};
struct mac_address {
#define WPA_STA_MFP BIT(3)
#define WPA_STA_TDLS_PEER BIT(4)
#define WPA_STA_AUTHENTICATED BIT(5)
+#define WPA_STA_ASSOCIATED BIT(6)
enum tdls_oper {
TDLS_DISCOVERY_REQ,
struct beacon_data beacon_csa;
struct beacon_data beacon_after;
- u16 counter_offset_beacon;
- u16 counter_offset_presp;
+ u16 counter_offset_beacon[2];
+ u16 counter_offset_presp[2];
};
/* TDLS peer capabilities for send_tdls_mgmt() */
void (*poll)(void *priv);
/**
+ * get_ifindex - Get interface index
+ * @priv: private driver interface data
+ *
+ * Returns: Interface index
+ */
+ unsigned int (*get_ifindex)(void *priv);
+
+ /**
* get_ifname - Get interface name
* @priv: private driver interface data
*
* @noack: Do not wait for this frame to be acked (disable retries)
* @freq: Frequency (in MHz) to send the frame on, or 0 to let the
* driver decide
+ * @csa_offs: Array of CSA offsets or %NULL
+ * @csa_offs_len: Number of elements in csa_offs
* Returns: 0 on success, -1 on failure
*/
int (*send_mlme)(void *priv, const u8 *data, size_t data_len,
- int noack, unsigned int freq);
+ int noack, unsigned int freq, const u16 *csa_offs,
+ size_t csa_offs_len);
/**
* update_ft_ies - Update FT (IEEE 802.11r) IEs
/**
* global_init - Global driver initialization
+ * @ctx: wpa_global pointer
* Returns: Pointer to private data (global), %NULL on failure
*
* This optional function is called to initialize the driver wrapper
* use init2() function instead of init() to get the pointer to global
* data available to per-interface initializer.
*/
- void * (*global_init)(void);
+ void * (*global_init)(void *ctx);
/**
* global_deinit - Global driver deinitialization
* @params: Station parameters
* Returns: 0 on success, -1 on failure
*
- * This function is used to add a station entry to the driver once the
- * station has completed association. This is only used if the driver
+ * This function is used to add or set (params->set 1) a station
+ * entry in the driver. Adding STA entries is used only if the driver
* does not take care of association processing.
*
- * With TDLS, this function is also used to add or set (params->set 1)
- * TDLS peer entries.
+ * With drivers that don't support full AP client state, this function
+ * is used to add a station entry to the driver once the station has
+ * completed association.
+ *
+ * With TDLS, this function is used to add or set (params->set 1)
+ * TDLS peer entries (even with drivers that do not support full AP
+ * client state).
*/
int (*sta_add)(void *priv, struct hostapd_sta_add_params *params);
* change interface address)
* @bridge: Bridge interface to use or %NULL if no bridge configured
* @use_existing: Whether to allow existing interface to be used
+ * @setup_ap: Whether to setup AP for %WPA_IF_AP_BSS interfaces
* Returns: 0 on success, -1 on failure
*/
int (*if_add)(void *priv, enum wpa_driver_if_type type,
const char *ifname, const u8 *addr, void *bss_ctx,
void **drv_priv, char *force_ifname, u8 *if_addr,
- const char *bridge, int use_existing);
+ const char *bridge, int use_existing, int setup_ap);
/**
* if_remove - Remove a virtual interface
* sched_scan - Request the driver to initiate scheduled scan
* @priv: Private driver interface data
* @params: Scan parameters
- * @interval: Interval between scan cycles in milliseconds
* Returns: 0 on success, -1 on failure
*
* This operation should be used for scheduled scan offload to
* and if not provided or if it returns -1, we fall back to
* normal host-scheduled scans.
*/
- int (*sched_scan)(void *priv, struct wpa_driver_scan_params *params,
- u32 interval);
+ int (*sched_scan)(void *priv, struct wpa_driver_scan_params *params);
/**
* stop_sched_scan - Request the driver to stop a scheduled scan
* set_current_cipher_suite - Set current cipher suite
* @priv: Private driver interface data
* @cs: EUI64 identifier
- * @cs_len: Length of the cs buffer in octets
* Returns: 0 on success, -1 on failure (or if not supported)
*/
- int (*set_current_cipher_suite)(void *priv, const u8 *cs,
- size_t cs_len);
+ int (*set_current_cipher_suite)(void *priv, u64 cs);
/**
* enable_controlled_port - Set controlled port status
* on. Local device is assuming P2P Client role.
*/
int (*set_prob_oper_freq)(void *priv, unsigned int freq);
+
+ /**
+ * abort_scan - Request the driver to abort an ongoing scan
+ * @priv: Private driver interface data
+ * Returns 0 on success, -1 on failure
+ */
+ int (*abort_scan)(void *priv);
+
+ /**
+ * configure_data_frame_filters - Request to configure frame filters
+ * @priv: Private driver interface data
+ * @filter_flags: The type of frames to filter (bitfield of
+ * WPA_DATA_FRAME_FILTER_FLAG_*)
+ * Returns: 0 on success or -1 on failure
+ */
+ int (*configure_data_frame_filters)(void *priv, u32 filter_flags);
+
+ /**
+ * get_ext_capab - Get extended capabilities for the specified interface
+ * @priv: Private driver interface data
+ * @type: Interface type for which to get extended capabilities
+ * @ext_capab: Extended capabilities fetched
+ * @ext_capab_mask: Extended capabilities mask
+ * @ext_capab_len: Length of the extended capabilities
+ * Returns: 0 on success or -1 on failure
+ */
+ int (*get_ext_capab)(void *priv, enum wpa_driver_if_type type,
+ const u8 **ext_capab, const u8 **ext_capab_mask,
+ unsigned int *ext_capab_len);
+
+ /**
+ * p2p_lo_start - Start offloading P2P listen to device
+ * @priv: Private driver interface data
+ * @freq: Listening frequency (MHz) for P2P listen
+ * @period: Length of the listen operation in milliseconds
+ * @interval: Interval for running the listen operation in milliseconds
+ * @count: Number of times to run the listen operation
+ * @device_types: Device primary and secondary types
+ * @dev_types_len: Number of bytes for device_types
+ * @ies: P2P IE and WSC IE for Probe Response frames
+ * @ies_len: Length of ies in bytes
+ * Returns: 0 on success or -1 on failure
+ */
+ int (*p2p_lo_start)(void *priv, unsigned int freq,
+ unsigned int period, unsigned int interval,
+ unsigned int count,
+ const u8 *device_types, size_t dev_types_len,
+ const u8 *ies, size_t ies_len);
+
+ /**
+ * p2p_lo_stop - Stop P2P listen offload
+ * @priv: Private driver interface data
+ * Returns: 0 on success or -1 on failure
+ */
+ int (*p2p_lo_stop)(void *priv);
+
+ /**
+ * set_default_scan_ies - Set default scan IEs
+ * @priv: Private driver interface data
+ * @ies: Scan default IEs buffer
+ * @ies_len: Length of IEs in bytes
+ * Returns: 0 on success or -1 on failure
+ *
+ * The driver can use these by default when there are no scan IEs coming
+ * in the subsequent scan requests. Also in case of one or more of IEs
+ * given in set_default_scan_ies() are missing in the subsequent scan
+ * request, the driver should merge the missing scan IEs in the scan
+ * request from the IEs set by set_default_scan_ies() in the Probe
+ * Request frames sent.
+ */
+ int (*set_default_scan_ies)(void *priv, const u8 *ies, size_t ies_len);
+
};
* on a DFS frequency by a driver that supports DFS Offload.
*/
EVENT_DFS_CAC_STARTED,
+
+ /**
+ * EVENT_P2P_LO_STOP - Notify that P2P listen offload is stopped
+ */
+ EVENT_P2P_LO_STOP,
};
* ptk_kek_len - The length of ptk_kek
*/
size_t ptk_kek_len;
+
+ /**
+ * subnet_status - The subnet status:
+ * 0 = unknown, 1 = unchanged, 2 = changed
+ */
+ u8 subnet_status;
} assoc_info;
/**
* struct interface_status - Data for EVENT_INTERFACE_STATUS
*/
struct interface_status {
+ unsigned int ifindex;
char ifname[100];
enum {
EVENT_INTERFACE_ADDED, EVENT_INTERFACE_REMOVED
* status_code - Status Code from (Re)association Response
*/
u16 status_code;
+
+ /**
+ * timed_out - Whether failure is due to timeout (etc.) rather
+ * than explicit rejection response from the AP.
+ */
+ int timed_out;
} assoc_reject;
struct timeout_event {
* @ssids: Scanned SSIDs (%NULL or zero-length SSID indicates wildcard
* SSID)
* @num_ssids: Number of entries in ssids array
+ * @external_scan: Whether the scan info is for an external scan
+ * @nl_scan_event: 1 if the source of this scan event is a normal scan,
+ * 0 if the source of the scan event is a vendor scan
*/
struct scan_info {
int aborted;
size_t num_freqs;
struct wpa_driver_scan_ssid ssids[WPAS_MAX_SCAN_SSIDS];
size_t num_ssids;
+ int external_scan;
+ int nl_scan_event;
} scan_info;
/**
u16 ch_width;
enum hostapd_hw_mode hw_mode;
} acs_selected_channels;
+
+ /**
+ * struct p2p_lo_stop - Reason code for P2P Listen offload stop event
+ * @reason_code: Reason for stopping offload
+ * P2P_LO_STOPPED_REASON_COMPLETE: Listen offload finished as
+ * scheduled.
+ * P2P_LO_STOPPED_REASON_RECV_STOP_CMD: Host requested offload to
+ * be stopped.
+ * P2P_LO_STOPPED_REASON_INVALID_PARAM: Invalid listen offload
+ * parameters.
+ * P2P_LO_STOPPED_REASON_NOT_SUPPORTED: Listen offload not
+ * supported by device.
+ */
+ struct p2p_lo_stop {
+ enum {
+ P2P_LO_STOPPED_REASON_COMPLETE = 0,
+ P2P_LO_STOPPED_REASON_RECV_STOP_CMD,
+ P2P_LO_STOPPED_REASON_INVALID_PARAM,
+ P2P_LO_STOPPED_REASON_NOT_SUPPORTED,
+ } reason_code;
+ } p2p_lo_stop;
};
/**
void wpa_supplicant_event(void *ctx, enum wpa_event_type event,
union wpa_event_data *data);
+/**
+ * wpa_supplicant_event_global - Report a driver event for wpa_supplicant
+ * @ctx: Context pointer (wpa_s); this is the ctx variable registered
+ * with struct wpa_driver_ops::init()
+ * @event: event type (defined above)
+ * @data: possible extra data for the event
+ *
+ * Same as wpa_supplicant_event(), but we search for the interface in
+ * wpa_global.
+ */
+void wpa_supplicant_event_global(void *ctx, enum wpa_event_type event,
+ union wpa_event_data *data);
/*
* The following inline functions are provided for convenience to simplify
struct wowlan_triggers *
wpa_get_wowlan_triggers(const char *wowlan_triggers,
const struct wpa_driver_capa *capa);
+/* Convert driver flag to string */
+const char * driver_flag_to_string(u64 flag);
/* NULL terminated array of linked in driver wrappers */
extern const struct wpa_driver_ops *const wpa_drivers[];
+
+/* Available drivers */
+
+#ifdef CONFIG_DRIVER_WEXT
+extern const struct wpa_driver_ops wpa_driver_wext_ops; /* driver_wext.c */
+#endif /* CONFIG_DRIVER_WEXT */
+#ifdef CONFIG_DRIVER_NL80211
+/* driver_nl80211.c */
+extern const struct wpa_driver_ops wpa_driver_nl80211_ops;
+#endif /* CONFIG_DRIVER_NL80211 */
+#ifdef CONFIG_DRIVER_HOSTAP
+extern const struct wpa_driver_ops wpa_driver_hostap_ops; /* driver_hostap.c */
+#endif /* CONFIG_DRIVER_HOSTAP */
+#ifdef CONFIG_DRIVER_BSD
+extern const struct wpa_driver_ops wpa_driver_bsd_ops; /* driver_bsd.c */
+#endif /* CONFIG_DRIVER_BSD */
+#ifdef CONFIG_DRIVER_OPENBSD
+/* driver_openbsd.c */
+extern const struct wpa_driver_ops wpa_driver_openbsd_ops;
+#endif /* CONFIG_DRIVER_OPENBSD */
+#ifdef CONFIG_DRIVER_NDIS
+extern struct wpa_driver_ops wpa_driver_ndis_ops; /* driver_ndis.c */
+#endif /* CONFIG_DRIVER_NDIS */
+#ifdef CONFIG_DRIVER_WIRED
+extern const struct wpa_driver_ops wpa_driver_wired_ops; /* driver_wired.c */
+#endif /* CONFIG_DRIVER_WIRED */
+#ifdef CONFIG_DRIVER_MACSEC_QCA
+/* driver_macsec_qca.c */
+extern const struct wpa_driver_ops wpa_driver_macsec_qca_ops;
+#endif /* CONFIG_DRIVER_MACSEC_QCA */
+#ifdef CONFIG_DRIVER_ROBOSWITCH
+/* driver_roboswitch.c */
+extern const struct wpa_driver_ops wpa_driver_roboswitch_ops;
+#endif /* CONFIG_DRIVER_ROBOSWITCH */
+#ifdef CONFIG_DRIVER_ATHEROS
+/* driver_atheros.c */
+extern const struct wpa_driver_ops wpa_driver_atheros_ops;
+#endif /* CONFIG_DRIVER_ATHEROS */
+#ifdef CONFIG_DRIVER_NONE
+extern const struct wpa_driver_ops wpa_driver_none_ops; /* driver_none.c */
+#endif /* CONFIG_DRIVER_NONE */
+
#endif /* DRIVER_H */
projects / mech_eap.git / blobdiff