* indicated through an event using the same sub command through
* @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are
* listed in qca_wlan_vendor_attr_sap_conditional_chan_switch.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the
+ * attributes defined in enum qca_wlan_gpio_attr.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities.
+ * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which
+ * capabilities are to be fetched and other
+ * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the
+ * requested capabilities.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension.
+ * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this
+ * command and event.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122,
QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123,
QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124,
+ QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125,
+ QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126,
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127,
};
};
/**
+ * enum qca_access_policy - Access control policy
+ *
+ * Access control policy is applied on the configured IE
+ * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE).
+ * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY.
+ *
+ * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match
+ * the specific configuration (IE) set, i.e., allow all the
+ * connections which do not match the configuration.
+ * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match
+ * the specific configuration (IE) set, i.e., deny all the
+ * connections which do not match the configuration.
+ */
+enum qca_access_policy {
+ QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED,
+ QCA_ACCESS_POLICY_DENY_UNLESS_LISTED,
+};
+
+/**
* enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture
* @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32)
* @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value
};
/* Attributes for data used by
- * QCA_NL80211_VENDOR_SUBCMD_SET_CONFIGURATION and
- * QCA_NL80211_VENDOR_SUBCMD_GET_CONFIGURATION subcommands.
+ * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
+ * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
*/
enum qca_wlan_vendor_attr_config {
QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID,
* packet count. The peer is disconnected once this threshold is
* reached. */
QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT,
+ /* Attribute used to set scan default IEs to the driver.
+ *
+ * These IEs can be used by scan operations that will be initiated by
+ * the driver/firmware.
+ *
+ * For further scan requests coming to the driver, these IEs should be
+ * merged with the IEs received along with scan request coming to the
+ * driver. If a particular IE is present in the scan default IEs but not
+ * present in the scan request, then that IE should be added to the IEs
+ * sent in the Probe Request frames for that scan request. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES,
+ /* Unsigned 32-bit attribute for generic commands */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND,
+ /* Unsigned 32-bit value attribute for generic commands */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE,
+ /* Unsigned 32-bit data attribute for generic command response */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA,
+ /* Unsigned 32-bit length attribute for
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH,
+ /* Unsigned 32-bit flags attribute for
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS,
+ /* Unsigned 32-bit, defining the access policy.
+ * See enum qca_access_policy. Used with
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY,
+ /* Sets the list of full set of IEs for which a specific access policy
+ * has to be applied. Used along with
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
+ * Zero length payload can be used to clear this access constraint. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST,
+ /* Unsigned 32-bit, specifies the interface index (netdev) for which the
+ * corresponding configurations are applied. If the interface index is
+ * not specified, the configurations are attributed to the respective
+ * wiphy. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX,
+ /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER,
/* keep last */
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1,
};
+/**
+ * enum qca_wlan_gpio_attr - Parameters for GPIO configuration
+ */
+enum qca_wlan_gpio_attr {
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0,
+ /* Unsigned 32-bit attribute for GPIO command */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND,
+ /* Unsigned 32-bit attribute for GPIO PIN number to configure */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM,
+ /* Unsigned 32-bit attribute for GPIO value to configure */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE,
+ /* Unsigned 32-bit attribute for GPIO pull type */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE,
+ /* Unsigned 32-bit attribute for GPIO interrupt mode */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST,
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
+ */
+enum qca_wlan_vendor_attr_get_hw_capability {
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID,
+ /* Antenna isolation
+ * An attribute used in the response.
+ * The content of this attribute is encoded in a byte array. Each byte
+ * value is an antenna isolation value. The array length is the number
+ * of antennas.
+ */
+ QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION,
+ /* Request HW capability
+ * An attribute used in the request.
+ * The content of this attribute is a u32 array for one or more of
+ * hardware capabilities (attribute IDs) that are being requested. Each
+ * u32 value has a value from this
+ * enum qca_wlan_vendor_attr_get_hw_capability
+ * identifying which capabilities are requested.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX =
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
+ * offload which is an extension for LL_STATS.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
+ * If MAC counters do not exceed the threshold, FW will report monitored
+ * link layer counters periodically as this setting. The first report is
+ * always triggered by this timer.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
+ * For each MAC layer counter, FW holds two copies. One is the current value.
+ * The other is the last report. Once a current counter's increment is larger
+ * than the threshold, FW will indicate that counter to host even if the
+ * monitoring timer does not expire.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
+ * failure code.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
+ * 1: TX packet discarded
+ * 2: No ACK
+ * 3: Postpone
+ */
+enum qca_wlan_vendor_attr_ll_stats_ext {
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0,
+
+ /* Attributes for configurations */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD,
+
+ /* Attributes for events */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG,
+
+ /* TX failure event */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS,
+
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX =
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1
+};
+
#endif /* QCA_VENDOR_H */