* @QCA_NL80211_VENDOR_SUBCMD_DFS_OFFLOAD_RADAR_DETECTED: Event used by driver,
* which supports DFS offloading, to indicate a radar pattern has been
* detected. The channel is now unusable.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START: Command used to
+ * start the P2P Listen offload function in device and pass the listen
+ * channel, period, interval, count, device types, and vendor specific
+ * information elements to the device driver and firmware.
+ * Uses the attributes defines in
+ * enum qca_wlan_vendor_attr_p2p_listen_offload.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP: Command/event used to
+ * indicate stop request/response of the P2P Listen offload function in
+ * device. As an event, it indicates either the feature stopped after it
+ * was already running or feature has actually failed to start. Uses the
+ * attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts
+ * beaconing, this sub command provides the driver, the frequencies on the
+ * 5 GHz band to check for any radar activity. Driver selects one channel
+ * from this priority list provided through
+ * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts
+ * to check for radar activity on it. If no radar activity is detected
+ * during the channel availability check period, driver internally switches
+ * to the selected frequency of operation. If the frequency is zero, driver
+ * internally selects a channel. The status of this conditional switch is
+ * indicated through an event using the same sub command through
+ * @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are
+ * listed in qca_wlan_vendor_attr_sap_conditional_chan_switch.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND: Set GPIO pins. This uses the
+ * attributes defined in enum qca_wlan_gpio_attr.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY: Fetch hardware capabilities.
+ * This uses @QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY to indicate which
+ * capabilities are to be fetched and other
+ * enum qca_wlan_vendor_attr_get_hw_capability attributes to return the
+ * requested capabilities.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT: Link layer statistics extension.
+ * enum qca_wlan_vendor_attr_ll_stats_ext attributes are used with this
+ * command and event.
*/
enum qca_nl80211_vendor_subcmds {
QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
QCA_NL80211_VENDOR_SUBCMD_SET_SAP_CONFIG = 118,
QCA_NL80211_VENDOR_SUBCMD_TSF = 119,
QCA_NL80211_VENDOR_SUBCMD_WISA = 120,
+ /* 121 - reserved for QCA */
+ QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122,
+ QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123,
+ QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124,
+ QCA_NL80211_VENDOR_SUBCMD_GPIO_CONFIG_COMMAND = 125,
+ QCA_NL80211_VENDOR_SUBCMD_GET_HW_CAPABILITY = 126,
+ QCA_NL80211_VENDOR_SUBCMD_LL_STATS_EXT = 127,
};
QCA_WLAN_VENDOR_ATTR_ROAM_AUTH_AFTER_LAST - 1
};
+enum qca_wlan_vendor_attr_p2p_listen_offload {
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INVALID = 0,
+ /* A 32-bit unsigned value; the P2P listen frequency (MHz); must be one
+ * of the social channels.
+ */
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CHANNEL,
+ /* A 32-bit unsigned value; the P2P listen offload period (ms).
+ */
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_PERIOD,
+ /* A 32-bit unsigned value; the P2P listen interval duration (ms).
+ */
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_INTERVAL,
+ /* A 32-bit unsigned value; number of interval times the firmware needs
+ * to run the offloaded P2P listen operation before it stops.
+ */
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_COUNT,
+ /* An array of arbitrary binary data with one or more 8-byte values.
+ * The device types include both primary and secondary device types.
+ */
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_DEVICE_TYPES,
+ /* An array of unsigned 8-bit characters; vendor information elements.
+ */
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_VENDOR_IE,
+ /* A 32-bit unsigned value; a control flag to indicate whether listen
+ * results need to be flushed to wpa_supplicant.
+ */
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_CTRL_FLAG,
+ /* A 8-bit unsigned value; reason code for P2P listen offload stop
+ * event.
+ */
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_STOP_REASON,
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_MAX =
+ QCA_WLAN_VENDOR_ATTR_P2P_LISTEN_OFFLOAD_AFTER_LAST - 1
+};
+
enum qca_wlan_vendor_attr_acs_offload {
QCA_WLAN_VENDOR_ATTR_ACS_CHANNEL_INVALID = 0,
QCA_WLAN_VENDOR_ATTR_ACS_PRIMARY_CHANNEL,
* band selection based on channel selection results.
* @QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS: Device supports
* simultaneous off-channel operations.
+ * @QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD: Device supports P2P
+ * Listen offload; a mechanism where the station's firmware takes care of
+ * responding to incoming Probe Request frames received from other P2P
+ * Devices whilst in Listen state, rather than having the user space
+ * wpa_supplicant do it. Information from received P2P requests are
+ * forwarded from firmware to host whenever the host processor wakes up.
* @NUM_QCA_WLAN_VENDOR_FEATURES: Number of assigned feature bits
*/
enum qca_wlan_vendor_features {
QCA_WLAN_VENDOR_FEATURE_KEY_MGMT_OFFLOAD = 0,
QCA_WLAN_VENDOR_FEATURE_SUPPORT_HW_MODE_ANY = 1,
QCA_WLAN_VENDOR_FEATURE_OFFCHANNEL_SIMULTANEOUS = 2,
+ QCA_WLAN_VENDOR_FEATURE_P2P_LISTEN_OFFLOAD = 3,
NUM_QCA_WLAN_VENDOR_FEATURES /* keep last */
};
};
/**
+ * enum qca_access_policy - Access control policy
+ *
+ * Access control policy is applied on the configured IE
+ * (QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE).
+ * To be set with QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY.
+ *
+ * @QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED: Deny Wi-Fi connections which match
+ * the specific configuration (IE) set, i.e., allow all the
+ * connections which do not match the configuration.
+ * @QCA_ACCESS_POLICY_DENY_UNLESS_LISTED: Accept Wi-Fi connections which match
+ * the specific configuration (IE) set, i.e., deny all the
+ * connections which do not match the configuration.
+ */
+enum qca_access_policy {
+ QCA_ACCESS_POLICY_ACCEPT_UNLESS_LISTED,
+ QCA_ACCESS_POLICY_DENY_UNLESS_LISTED,
+};
+
+/**
* enum qca_vendor_attr_get_tsf: Vendor attributes for TSF capture
* @QCA_WLAN_VENDOR_ATTR_TSF_CMD: enum qca_tsf_operation (u32)
* @QCA_WLAN_VENDOR_ATTR_TSF_TIMER_VALUE: Unsigned 64 bit TSF timer value
*
* This vendor element may be included in GO Negotiation Request, P2P
* Invitation Request, and Provision Discovery Request frames.
+ *
+ * @QCA_VENDOR_ELEM_HE_CAPAB: HE Capabilities element.
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID. The payload of this
+ * vendor specific element is defined by the latest P802.11ax draft.
+ * Please note that the draft is still work in progress and this element
+ * payload is subject to change.
+ *
+ * @QCA_VENDOR_ELEM_HE_OPER: HE Operation element.
+ * This element can be used for pre-standard publication testing of HE
+ * before P802.11ax draft assigns the element ID. The payload of this
+ * vendor specific element is defined by the latest P802.11ax draft.
+ * Please note that the draft is still work in progress and this element
+ * payload is subject to change.
*/
enum qca_vendor_element_id {
QCA_VENDOR_ELEM_P2P_PREF_CHAN_LIST = 0,
+ QCA_VENDOR_ELEM_HE_CAPAB = 1,
+ QCA_VENDOR_ELEM_HE_OPER = 2,
};
/**
};
/* Attributes for data used by
- * QCA_NL80211_VENDOR_SUBCMD_SET_CONFIGURATION and
- * QCA_NL80211_VENDOR_SUBCMD_GET_CONFIGURATION subcommands.
+ * QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION and
+ * QCA_NL80211_VENDOR_SUBCMD_GET_WIFI_CONFIGURATION subcommands.
*/
enum qca_wlan_vendor_attr_config {
QCA_WLAN_VENDOR_ATTR_CONFIG_INVALID,
/* 8-bit unsigned value to configure the maximum RX MPDU for
* aggregation. */
QCA_WLAN_VENDOR_ATTR_CONFIG_RX_MPDU_AGGREGATION,
+ /* 8-bit unsigned value to configure the Non aggregrate/11g sw
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_NON_AGG_RETRY,
+ /* 8-bit unsigned value to configure the aggregrate sw
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_AGG_RETRY,
+ /* 8-bit unsigned value to configure the MGMT frame
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_MGMT_RETRY,
+ /* 8-bit unsigned value to configure the CTRL frame
+ * retry threshold (0 disable, 31 max). */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_CTRL_RETRY,
+ /* 8-bit unsigned value to configure the propagation delay for
+ * 2G/5G band (0~63, units in us) */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_PROPAGATION_DELAY,
+ /* Unsigned 32-bit value to configure the number of unicast TX fail
+ * packet count. The peer is disconnected once this threshold is
+ * reached. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_TX_FAIL_COUNT,
+ /* Attribute used to set scan default IEs to the driver.
+ *
+ * These IEs can be used by scan operations that will be initiated by
+ * the driver/firmware.
+ *
+ * For further scan requests coming to the driver, these IEs should be
+ * merged with the IEs received along with scan request coming to the
+ * driver. If a particular IE is present in the scan default IEs but not
+ * present in the scan request, then that IE should be added to the IEs
+ * sent in the Probe Request frames for that scan request. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_SCAN_DEFAULT_IES,
+ /* Unsigned 32-bit attribute for generic commands */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_COMMAND,
+ /* Unsigned 32-bit value attribute for generic commands */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_VALUE,
+ /* Unsigned 32-bit data attribute for generic command response */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA,
+ /* Unsigned 32-bit length attribute for
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_LENGTH,
+ /* Unsigned 32-bit flags attribute for
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_DATA */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_GENERIC_FLAGS,
+ /* Unsigned 32-bit, defining the access policy.
+ * See enum qca_access_policy. Used with
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY,
+ /* Sets the list of full set of IEs for which a specific access policy
+ * has to be applied. Used along with
+ * QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY to control the access.
+ * Zero length payload can be used to clear this access constraint. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_ACCESS_POLICY_IE_LIST,
+ /* Unsigned 32-bit, specifies the interface index (netdev) for which the
+ * corresponding configurations are applied. If the interface index is
+ * not specified, the configurations are attributed to the respective
+ * wiphy. */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_IFINDEX,
+ /* 8-bit unsigned value to trigger QPower: 1-Enable, 0-Disable */
+ QCA_WLAN_VENDOR_ATTR_CONFIG_QPOWER,
/* keep last */
QCA_WLAN_VENDOR_ATTR_CONFIG_AFTER_LAST,
QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1,
};
+/**
+ * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
+ * conditional channel switch
+ */
+enum qca_wlan_vendor_attr_sap_conditional_chan_switch {
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0,
+ /* Priority based frequency list (an array of u32 values in host byte
+ * order) */
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1,
+ /* Status of the conditional switch (u32).
+ * 0: Success, Non-zero: Failure
+ */
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2,
+
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX =
+ QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_gpio_attr - Parameters for GPIO configuration
+ */
+enum qca_wlan_gpio_attr {
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INVALID = 0,
+ /* Unsigned 32-bit attribute for GPIO command */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_COMMAND,
+ /* Unsigned 32-bit attribute for GPIO PIN number to configure */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PINNUM,
+ /* Unsigned 32-bit attribute for GPIO value to configure */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_VALUE,
+ /* Unsigned 32-bit attribute for GPIO pull type */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_PULL_TYPE,
+ /* Unsigned 32-bit attribute for GPIO interrupt mode */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_INTR_MODE,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST,
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_MAX =
+ QCA_WLAN_VENDOR_ATTR_GPIO_PARAM_LAST - 1
+};
+
+/**
+ * enum qca_wlan_vendor_attr_get_hw_capability - Wi-Fi hardware capability
+ */
+enum qca_wlan_vendor_attr_get_hw_capability {
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_INVALID,
+ /* Antenna isolation
+ * An attribute used in the response.
+ * The content of this attribute is encoded in a byte array. Each byte
+ * value is an antenna isolation value. The array length is the number
+ * of antennas.
+ */
+ QCA_WLAN_VENDOR_ATTR_ANTENNA_ISOLATION,
+ /* Request HW capability
+ * An attribute used in the request.
+ * The content of this attribute is a u32 array for one or more of
+ * hardware capabilities (attribute IDs) that are being requested. Each
+ * u32 value has a value from this
+ * enum qca_wlan_vendor_attr_get_hw_capability
+ * identifying which capabilities are requested.
+ */
+ QCA_WLAN_VENDOR_ATTR_GET_HW_CAPABILITY,
+
+ /* keep last */
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST,
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_MAX =
+ QCA_WLAN_VENDOR_ATTR_HW_CAPABILITY_AFTER_LAST - 1,
+};
+
+/**
+ * enum qca_wlan_vendor_attr_ll_stats_ext - Attributes for MAC layer monitoring
+ * offload which is an extension for LL_STATS.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD: Monitoring period. Unit in ms.
+ * If MAC counters do not exceed the threshold, FW will report monitored
+ * link layer counters periodically as this setting. The first report is
+ * always triggered by this timer.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD: It is a percentage (1-99).
+ * For each MAC layer counter, FW holds two copies. One is the current value.
+ * The other is the last report. Once a current counter's increment is larger
+ * than the threshold, FW will indicate that counter to host even if the
+ * monitoring timer does not expire.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG: Peer STA power state change
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID: TID of MSDU
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU: Count of MSDU with the same
+ * failure code.
+ * @QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS: TX failure code
+ * 1: TX packet discarded
+ * 2: No ACK
+ * 3: Postpone
+ */
+enum qca_wlan_vendor_attr_ll_stats_ext {
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_INVALID = 0,
+
+ /* Attributes for configurations */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_PERIOD,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_CFG_THRESHOLD,
+
+ /* Attributes for events */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_PEER_PS_CHG,
+
+ /* TX failure event */
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TID,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_NUM_MSDU,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_TX_STATUS,
+
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST,
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_MAX =
+ QCA_WLAN_VENDOR_ATTR_LL_STATS_EXT_LAST - 1
+};
+
#endif /* QCA_VENDOR_H */