TDLS: Declare tdls_testing as extern in a header file

[mech_eap.git] / wpa_supplicant / README

diff --git a/wpa_supplicant/README b/wpa_supplicant/README
index bc3d6ab..11ab01a 100644 (file)
--- a/wpa_supplicant/README
+++ b/wpa_supplicant/README
@@ -72,11 +72,13 @@ Supported WPA/IEEE 802.11i features:
   * EAP-TTLS/CHAP
   * EAP-SIM
   * EAP-AKA
+  * EAP-AKA'
   * EAP-PSK
   * EAP-PAX
   * EAP-SAKE
   * EAP-IKEv2
   * EAP-GPSK
+  * EAP-pwd
   * LEAP (note: requires special support from the driver for IEEE 802.11
          authentication)
   (following methods are supported, but since they do not generate keying
@@ -314,15 +316,17 @@ CONFIG_EAP_GTC=y
 CONFIG_EAP_OTP=y
 CONFIG_EAP_SIM=y
 CONFIG_EAP_AKA=y
+CONFIG_EAP_AKA_PRIME=y
 CONFIG_EAP_PSK=y
 CONFIG_EAP_SAKE=y
 CONFIG_EAP_GPSK=y
 CONFIG_EAP_PAX=y
 CONFIG_EAP_LEAP=y
 CONFIG_EAP_IKEV2=y
+CONFIG_EAP_PWD=y
 
 Following option can be used to include GSM SIM/USIM interface for GSM/UMTS
-authentication algorithm (for EAP-SIM/EAP-AKA). This requires pcsc-lite
+authentication algorithm (for EAP-SIM/EAP-AKA/EAP-AKA'). This requires pcsc-lite
 (http://www.linuxnet.com/) for smart card access.
 
 CONFIG_PCSC=y
@@ -406,7 +410,7 @@ usage:
   wpa_supplicant [-BddfhKLqqtuvW] [-P<pid file>] [-g<global ctrl>] \
         [-G<group>] \
         -i<ifname> -c<config file> [-C<ctrl>] [-D<driver>] [-p<driver_param>] \
-        [-b<br_ifname> [-N -i<ifname> -c<conf> [-C<ctrl>] [-D<driver>] \
+        [-b<br_ifname> [-MN -i<ifname> -c<conf> [-C<ctrl>] [-D<driver>] \
         [-p<driver_param>] [-b<br_ifname>] [-m<P2P Device config file>] ...
 
 options:
@@ -430,6 +434,7 @@ options:
   -u = enable DBus control interface
   -v = show version
   -W = wait for a control interface monitor before starting
+  -M = start describing matching interface
   -N = start describing new interface
   -m = Configuration file for the P2P Device
 
@@ -472,6 +477,22 @@ wpa_supplicant \
        -c wpa2.conf -i wlan1 -D wext
 
 
+If the interfaces on which wpa_supplicant is to run are not known or do
+not exist, wpa_supplicant can match an interface when it arrives. Each
+matched interface is separated with -M argument and the -i argument now
+allows for pattern matching.
+
+As an example, the following command would start wpa_supplicant for a
+specific wired interface called lan0, any interface starting with wlan
+and lastly any other interface. Each match has its own configuration
+file, and for the wired interface a specific driver has also been given.
+
+wpa_supplicant \
+       -M -c wpa_wired.conf -ilan0 -D wired \
+       -M -c wpa1.conf -iwlan* \
+       -M -c wpa2.conf
+
+
 If the interface is added in a Linux bridge (e.g., br0), the bridge
 interface needs to be configured to wpa_supplicant in addition to the
 main interface: