# the driver reports successful association; each network block should have
# explicit security policy (i.e., only one option in the lists) for
# key_mgmt, pairwise, group, proto variables
+# Note: ap_scan=2 should not be used with the nl80211 driver interface (the
+# current Linux interface). ap_scan=1 is optimized work working with nl80211.
+# For finding networks using hidden SSID, scan_ssid=1 in the network block can
+# be used with nl80211.
# When using IBSS or AP mode, ap_scan=2 mode can force the new network to be
# created immediately regardless of scan results. ap_scan=1 mode will first try
# to scan for existing networks and only if no matches with the enabled
# networks are found, a new IBSS or AP mode network is created.
ap_scan=1
+# Whether to force passive scan for network connection
+#
+# By default, scans will send out Probe Request frames on channels that allow
+# active scanning. This advertise the local station to the world. Normally this
+# is fine, but users may wish to do passive scanning where the radio should only
+# listen quietly for Beacon frames and not send any Probe Request frames. Actual
+# functionality may be driver dependent.
+#
+# This parameter can be used to force only passive scanning to be used
+# for network connection cases. It should be noted that this will slow
+# down scan operations and reduce likelihood of finding the AP. In
+# addition, some use cases will override this due to functional
+# requirements, e.g., for finding an AP that uses hidden SSID
+# (scan_ssid=1) or P2P device discovery.
+#
+# 0: Do normal scans (allow active scans) (default)
+# 1: Do passive scans.
+#passive_scan=0
+
# MPM residency
# By default, wpa_supplicant implements the mesh peering manager (MPM) for an
# open mesh. However, if the driver can implement the MPM, you may set this to
fast_reauth=1
# OpenSSL Engine support
-# These options can be used to load OpenSSL engines.
+# These options can be used to load OpenSSL engines in special or legacy
+# modes.
# The two engines that are supported currently are shown below:
# They are both from the opensc project (http://www.opensc.org/)
-# By default no engines are loaded.
+# By default the PKCS#11 engine is loaded if the client_cert or
+# private_key option appear to be a PKCS#11 URI, and these options
+# should not need to be used explicitly.
# make the opensc engine available
#opensc_engine_path=/usr/lib/opensc/engine_opensc.so
# make the pkcs11 engine available
# up to the limit of 300 seconds (3, 9, 27 ... 300)
# For periodic module, parameters would be <fixed interval>
#autoscan=periodic:30
-# So a delay of 30 seconds will be applied between each scan
+# So a delay of 30 seconds will be applied between each scan.
+# Note: If sched_scan_plans are configured and supported by the driver,
+# autoscan is ignored.
# filter_ssids - SSID-based scan result filtering
# 0 = do not filter scan results (default)
# Protected Management Frames default
# This parameter can be used to set the default behavior for the ieee80211w
-# parameter. By default, PMF is disabled unless enabled with the global pmf=1/2
-# parameter or with the per-network ieee80211w=1/2 parameter. With pmf=1/2, PMF
-# is enabled/required by default, but can be disabled with the per-network
-# ieee80211w parameter.
+# parameter for RSN networks. By default, PMF is disabled unless enabled with
+# the global pmf=1/2 parameter or with the per-network ieee80211w=1/2 parameter.
+# With pmf=1/2, PMF is enabled/required by default, but can be disabled with the
+# per-network ieee80211w parameter. This global default value does not apply
+# for non-RSN networks (key_mgmt=NONE) since PMF is available only when using
+# RSN.
#pmf=0
# Enabled SAE finite cyclic groups in preference order
# matching network block
#auto_interworking=0
+# GAS Address3 field behavior
+# 0 = P2P specification (Address3 = AP BSSID); default
+# 1 = IEEE 802.11 standard compliant (Address3 = Wildcard BSSID when
+# sent to not-associated AP; if associated, AP BSSID)
+#gas_address3=0
+
# credential block
#
# Each credential used for automatic network selection is configured as a set
# (EAP-TLS). Full path to the file should be used since working
# directory may change when wpa_supplicant is run in the background.
#
+# Certificates from PKCS#11 tokens can be referenced by a PKCS#11 URI.
+#
+# For example: private_key="pkcs11:manufacturer=piv_II;id=%01"
+#
# Alternatively, a named configuration blob can be used by setting
# this to blob://blob_name.
#
# used since working directory may change when wpa_supplicant is run
# in the background.
#
+# Keys in PKCS#11 tokens can be referenced by a PKCS#11 URI.
+# For example: private_key="pkcs11:manufacturer=piv_II;id=%01"
+#
# Windows certificate store can be used by leaving client_cert out and
# configuring private_key in one of the following formats:
#
# 0 = do not use OCSP stapling (TLS certificate status extension)
# 1 = try to use OCSP stapling, but not require response
# 2 = require valid OCSP stapling response
+# 3 = require valid OCSP stapling response for all not-trusted
+# certificates in the server certificate chain
#
# sim_num: Identifier for which SIM to use in multi-SIM devices
#
# Hotspot 2.0
# hs20=1
+# Scheduled scan plans
+#
+# A space delimited list of scan plans. Each scan plan specifies the scan
+# interval and number of iterations, delimited by a colon. The last scan plan
+# will run infinitely and thus must specify only the interval and not the number
+# of iterations.
+#
+# The driver advertises the maximum number of scan plans supported. If more scan
+# plans than supported are configured, only the first ones are set (up to the
+# maximum supported). The last scan plan that specifies only the interval is
+# always set as the last plan.
+#
+# If the scan interval or the number of iterations for a scan plan exceeds the
+# maximum supported, it will be set to the maximum supported value.
+#
+# Format:
+# sched_scan_plans=<interval:iterations> <interval:iterations> ... <interval>
+#
+# Example:
+# sched_scan_plans=10:100 20:200 30
+
+# Multi Band Operation (MBO) non-preferred channels
+# A space delimited list of non-preferred channels where each channel is a colon
+# delimited list of values. Reason detail is optional.
+# Format:
+# non_pref_chan=<oper_class>:<chan>:<preference>:<reason>[:reason_detail]
+# Example:
+# non_pref_chan="81:5:10:2:0 81:1:0:2:0 81:9:0:2"
+
+# MBO Cellular Data Capabilities
+# 1 = Cellular data connection available
+# 2 = Cellular data connection not available
+# 3 = Not cellular capable (default)
+#mbo_cell_capa=3
+
# network block
#
# Each network (usually AP's sharing the same SSID) is configured as a separate
# an IBSS network with the configured SSID is already present, the frequency of
# the network will be used instead of this configured value.
#
+# pbss: Whether to use PBSS. Relevant to IEEE 802.11ad networks only.
+# 0 = do not use PBSS
+# 1 = use PBSS
+# 2 = don't care (not allowed in AP mode)
+# Used together with mode configuration. When mode is AP, it means to start a
+# PCP instead of a regular AP. When mode is infrastructure it means connect
+# to a PCP instead of AP. In this mode you can also specify 2 (don't care)
+# which means connect to either PCP or AP.
+# P2P_GO and P2P_GROUP_FORMATION modes must use PBSS in IEEE 802.11ad network.
+# For more details, see IEEE Std 802.11ad-2012.
+#
# scan_freq: List of frequencies to scan
# Space-separated list of frequencies in MHz to scan when searching for this
# BSS. If the subset of channels used by the network is known, this option can
# IEEE8021X = IEEE 802.1X using EAP authentication and (optionally) dynamically
# generated WEP keys
# NONE = WPA is not used; plaintext or static WEP could be used
+# WPA-NONE = WPA-None for IBSS (deprecated; use proto=RSN key_mgmt=WPA-PSK
+# instead)
+# FT-PSK = Fast BSS Transition (IEEE 802.11r) with pre-shared key
+# FT-EAP = Fast BSS Transition (IEEE 802.11r) with EAP authentication
# WPA-PSK-SHA256 = Like WPA-PSK but using stronger SHA256-based algorithms
# WPA-EAP-SHA256 = Like WPA-EAP but using stronger SHA256-based algorithms
+# SAE = Simultaneous authentication of equals; pre-shared key/password -based
+# authentication with stronger security than WPA-PSK especially when using
+# not that strong password
+# FT-SAE = SAE with FT
+# WPA-EAP-SUITE-B = Suite B 128-bit level
+# WPA-EAP-SUITE-B-192 = Suite B 192-bit level
+# OSEN = Hotspot 2.0 Rel 2 online signup connection
# If not set, this defaults to: WPA-PSK WPA-EAP
#
# ieee80211w: whether management frame protection is enabled
# that have issues interoperating with updated TLS version)
# tls_disable_tlsv1_2=1 - disable use of TLSv1.2 (a workaround for AAA servers
# that have issues interoperating with updated TLS version)
+# tls_ext_cert_check=0 - No external server certificate validation (default)
+# tls_ext_cert_check=1 - External server certificate validation enabled; this
+# requires an external program doing validation of server certificate
+# chain when receiving CTRL-RSP-EXT_CERT_CHECK event from the control
+# interface and report the result of the validation with
+# CTRL-RSP_EXT_CERT_CHECK.
#
# Following certificate/private key fields are used in inner Phase2
# authentication when using EAP-TTLS or EAP-PEAP.
# 0 = do not use OCSP stapling (TLS certificate status extension)
# 1 = try to use OCSP stapling, but not require response
# 2 = require valid OCSP stapling response
+# 3 = require valid OCSP stapling response for all not-trusted
+# certificates in the server certificate chain
#
# openssl_ciphers: OpenSSL specific cipher configuration
# This can be used to override the global openssl_ciphers configuration
# number of authentication servers. Strict EAP conformance mode can be
# configured by disabling workarounds with eap_workaround=0.
+# update_identifier: PPS MO ID
+# (Hotspot 2.0 PerProviderSubscription/UpdateIdentifier)
+
# Station inactivity limit
#
# If a station does not send anything in ap_max_inactivity seconds, an
# Beacon interval (default: 100 TU)
#beacon_int=100
+# WPS in AP mode
+# 0 = WPS enabled and configured (default)
+# 1 = WPS disabled
+#wps_disabled=0
+
# MAC address policy
# 0 = use permanent MAC address
# 1 = use random MAC address for each ESS connection
# 2: MCS 0-9
# 3: not supported
+##### Fast Session Transfer (FST) support #####################################
+#
+# The options in this section are only available when the build configuration
+# option CONFIG_FST is set while compiling hostapd. They allow this interface
+# to be a part of FST setup.
+#
+# FST is the transfer of a session from a channel to another channel, in the
+# same or different frequency bands.
+#
+# For detals, see IEEE Std 802.11ad-2012.
+
+# Identifier of an FST Group the interface belongs to.
+#fst_group_id=bond0
+
+# Interface priority within the FST Group.
+# Announcing a higher priority for an interface means declaring it more
+# preferable for FST switch.
+# fst_priority is in 1..255 range with 1 being the lowest priority.
+#fst_priority=100
+
+# Default LLT value for this interface in milliseconds. The value used in case
+# no value provided during session setup. Default is 50 msec.
+# fst_llt is in 1..4294967 range (due to spec limitation, see 10.32.2.2
+# Transitioning between states).
+#fst_llt=100
+
# Example blocks:
# Simple case: WPA-PSK, PSK as an ASCII passphrase, allow all valid ciphers
group=CCMP TKIP
identity="user@example.com"
ca_cert="/etc/cert/ca.pem"
- client_cert="/etc/cert/user.pem"
-
- engine=1
-
- # The engine configured here must be available. Look at
- # OpenSSL engine support in the global section.
- # The key available through the engine must be the private key
- # matching the client certificate configured above.
-
- # use the opensc engine
- #engine_id="opensc"
- #key_id="45"
- # use the pkcs11 engine
- engine_id="pkcs11"
- key_id="id_45"
+ # Certificate and/or key identified by PKCS#11 URI (RFC7512)
+ client_cert="pkcs11:manufacturer=piv_II;id=%01"
+ private_key="pkcs11:manufacturer=piv_II;id=%01"
# Optional PIN configuration; this can be left out and PIN will be
# asked through the control interface
projects / mech_eap.git / blobdiff