Update ChangeLog files for v2.6

This adds a summary of new changes since the last update.

Signed-off-by: Jouni Malinen <j@w1.fi>

diff --git a/hostapd/ChangeLog b/hostapd/ChangeLog
index f266f86..30b1472 100644 (file)
--- a/hostapd/ChangeLog
+++ b/hostapd/ChangeLog
@@ -5,7 +5,7 @@ ChangeLog for hostapd
          [http://w1.fi/security/2015-7/] (CVE-2015-5314)
        * fixed WPS configuration update vulnerability with malformed passphrase
          [http://w1.fi/security/2016-1/] (CVE-2016-4476)
-       * extended channel switch support fot VHT bandwidth changes
+       * extended channel switch support for VHT bandwidth changes
        * added support for configuring new ANQP-elements with
          anqp_elem=<InfoID>:<hexdump of payload>
        * fixed Suite B 192-bit AKM to use proper PMK length
@@ -30,6 +30,8 @@ ChangeLog for hostapd
          - minimal support for PKCS #12
          - support OCSP stapling (including ocsp_multi)
        * added support for OpenSSL 1.1 API changes
+         - drop support for OpenSSL 0.9.8
+         - drop support for OpenSSL 1.0.0
        * EAP-PEAP: support fast-connect crypto binding
        * RADIUS
          - fix Called-Station-Id to not escape SSID
@@ -41,18 +43,34 @@ ChangeLog for hostapd
            Tunnel_password case
          - update full message for interim accounting updates
          - add Acct-Delay-Time into Accounting messages
+         - add require_message_authenticator configuration option to require
+           CoA/Disconnect-Request packets to be authenticated
        * started to postpone WNM-Notification frame sending by 100 ms so that
          the STA has some more time to configure the key before this frame is
          received after the 4-way handshake
        * VHT: added interoperability workaround for 80+80 and 160 MHz channels
        * extended VLAN support (per-STA vif, etc.)
        * fixed PMKID derivation with SAE
-       * nl80211: added support for full station state operations
+       * nl80211
+         - added support for full station state operations
+         - fix IEEE 802.1X/WEP EAP reauthentication and rekeying to use
+           unencrypted EAPOL frames
        * added initial MBO support; number of extensions to WNM BSS Transition
          Management
        * added initial functionality for location related operations
        * added assocresp_elements parameter to allow vendor specific elements
          to be added into (Re)Association Response frames
+       * improved Public Action frame addressing
+         - use Address 3 = wildcard BSSID in GAS response if a query from an
+           unassociated STA used that address
+         - fix TX status processing for Address 3 = wildcard BSSID
+         - add gas_address3 configuration parameter to control Address 3
+           behavior
+       * added command line parameter -i to override interface parameter in
+         hostapd.conf
+       * added command completion support to hostapd_cli
+       * added passive client taxonomy determination (CONFIG_TAXONOMY=y
+         compile option and "SIGNATURE <addr>" control interface command)
        * number of small fixes
 
 2015-09-27 - v2.5

diff --git a/wpa_supplicant/ChangeLog b/wpa_supplicant/ChangeLog
index a97463d..e62d8c7 100644 (file)
--- a/wpa_supplicant/ChangeLog
+++ b/wpa_supplicant/ChangeLog
@@ -23,8 +23,20 @@ ChangeLog for wpa_supplicant
          - fix PMKID derivation
          - improve robustness on various exchanges
          - fix peer link counting in reconnect case
+         - improve mesh joining behavior
+         - allow DTIM period to be configured
+         - allow HT to be disabled (disable_ht=1)
          - add MESH_PEER_ADD and MESH_PEER_REMOVE commands
          - add support for PMKSA caching
+         - add minimal support for SAE group negotiation
+         - allow pairwise/group cipher to be configured in the network profile
+         - use ieee80211w profile parameter to enable/disable PMF and derive
+           a separate TX IGTK if PMF is enabled instead of using MGTK
+           incorrectly
+         - fix AEK and MTK derivation
+         - remove GTKdata and IGTKdata from Mesh Peering Confirm/Close
+         - note: these changes are not fully backwards compatible for secure
+           (RSN) mesh network
        * fixed PMKID derivation with SAE
        * added support for requesting and fetching arbitrary ANQP-elements
          without internal support in wpa_supplicant for the specific element
@@ -69,7 +81,7 @@ ChangeLog for wpa_supplicant
        * extended INTERFACE_ADD command to allow certain type (sta/ap)
          interface to be created
        * fixed and improved various FST operations
-       * added 80+80 MHz VHT support for IBSS/mesh
+       * added 80+80 MHz and 160 MHz VHT support for IBSS/mesh
        * fixed SIGNAL_POLL in IBSS and mesh cases
        * added an option to abort an ongoing scan (used to speed up connection
          and can also be done with the new ABORT_SCAN command)
@@ -104,7 +116,7 @@ ChangeLog for wpa_supplicant
        * enabled ACS support for AP mode operations with wpa_supplicant
        * EAP-PEAP: fixed interoperability issue with Windows 2012r2 server
          ("Invalid Compound_MAC in cryptobinding TLV")
-       * EAP-TTLS; fixed success after fragmented final Phase 2 message
+       * EAP-TTLS: fixed success after fragmented final Phase 2 message
        * VHT: added interoperability workaround for 80+80 and 160 MHz channels
        * WNM: workaround for broken AP operating class behavior
        * added kqueue(2) support for eloop (CONFIG_ELOOP_KQUEUE)
@@ -112,6 +124,8 @@ ChangeLog for wpa_supplicant
          - add support for full station state operations
          - do not add NL80211_ATTR_SMPS_MODE attribute if HT is disabled
          - add NL80211_ATTR_PREV_BSSID with Connect command
+         - fix IEEE 802.1X/WEP EAP reauthentication and rekeying to use
+           unencrypted EAPOL frames
        * added initial MBO support; number of extensions to WNM BSS Transition
          Management
        * added support for PBSS/PCP and P2P on 60 GHz
@@ -123,6 +137,11 @@ ChangeLog for wpa_supplicant
        * started to ignore pmf=1/2 parameter for non-RSN networks
        * added wps_disabled=1 network profile parameter to allow AP mode to
          be started without enabling WPS
+       * wpa_cli: added action script support for AP-ENABLED and AP-DISABLED
+         events
+       * improved Public Action frame addressing
+         - add gas_address3 configuration parameter to control Address 3
+           behavior
        * number of small fixes
 
 2015-09-27 - v2.5