QCA vendor command to configure conditional switch channel for AP

This commit introduces a new vendor sub command
QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH and associated
attributes which aim to configure selected frequencies on which the AP
can conditionally switch onto for preferred operation.

Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>

diff --git a/src/common/qca-vendor.h b/src/common/qca-vendor.h
index ff8cef9..afc3c2f 100644 (file)
--- a/src/common/qca-vendor.h
+++ b/src/common/qca-vendor.h
@@ -102,6 +102,19 @@ enum qca_radiotap_vendor_ids {
  *     device. As an event, it indicates either the feature stopped after it
  *     was already running or feature has actually failed to start. Uses the
  *     attributes defines in enum qca_wlan_vendor_attr_p2p_listen_offload.
+ *
+ * @QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH: After AP starts
+ *     beaconing, this sub command provides the driver, the frequencies on the
+ *     5 GHz band to check for any radar activity. Driver selects one channel
+ *     from this priority list provided through
+ *     @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST and starts
+ *     to check for radar activity on it. If no radar activity is detected
+ *     during the channel availability check period, driver internally switches
+ *     to the selected frequency of operation. If the frequency is zero, driver
+ *     internally selects a channel. The status of this conditional switch is
+ *     indicated through an event using the same sub command through
+ *     @QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS. Attributes are
+ *     listed in qca_wlan_vendor_attr_sap_conditional_chan_switch.
  */
 enum qca_nl80211_vendor_subcmds {
        QCA_NL80211_VENDOR_SUBCMD_UNSPEC = 0,
@@ -186,6 +199,7 @@ enum qca_nl80211_vendor_subcmds {
        /* 121 - reserved for QCA */
        QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_START = 122,
        QCA_NL80211_VENDOR_SUBCMD_P2P_LISTEN_OFFLOAD_STOP = 123,
+       QCA_NL80211_VENDOR_SUBCMD_SAP_CONDITIONAL_CHAN_SWITCH = 124,
 };
 
 
@@ -661,4 +675,23 @@ enum qca_wlan_vendor_attr_sap_config {
        QCA_WLAN_VENDOR_ATTR_SAP_CONFIG_AFTER_LAST - 1,
 };
 
+/**
+ * enum qca_wlan_vendor_attr_sap_conditional_chan_switch - Parameters for AP
+ *                                     conditional channel switch
+ */
+enum qca_wlan_vendor_attr_sap_conditional_chan_switch {
+       QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_INVALID = 0,
+       /* Priority based frequency list (an array of u32 values in host byte
+        * order) */
+       QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_FREQ_LIST = 1,
+       /* Status of the conditional switch (u32).
+        * 0: Success, Non-zero: Failure
+        */
+       QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_STATUS = 2,
+
+       QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST,
+       QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_MAX =
+       QCA_WLAN_VENDOR_ATTR_SAP_CONDITIONAL_CHAN_SWITCH_AFTER_LAST - 1,
+};
+
 #endif /* QCA_VENDOR_H */